Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About ravikantt
ravikantt
Beginner
B. Tech in ECE stream, working in Network domain since 2010, Good with Routing, MPLS
Stats
Member since
06-01-2013
29
Posts
5
Helpful
2
Solutions
06-05-2014
01:41 AM
Hi folks, I was trying to configure a secondary IOS file for bootingon 2960X switch. Actually i was doing a IOS upgradation, & as precaution I'm keeping old IOS file in the flash & trying to make it as secondary image to boo,t in case switch with new IOS is not able to boot , it would fall back to old IOS & boot with it. I've seen the some sugguestions of putting multiple "boot system" command in order in which I want it boot with, but that seems not the case over here coz I'm not able to see "boot system" command in the show running-config. Please suggest if there's a way around for this!
... View more
Labels:
05-21-2014
03:56 AM
Hmm..... That's not the case.... Tried this already
Even I've seen its kinda default command in some old IOS....... But not getting a firm URL or link to confirm it..... So not sure if it's issue with IOS or something else
... View more
05-20-2014
09:51 PM
Hii Guys! I'm trying to remove the "radius-server-source-port -1645-1646" command but it's not happening.. Command executes but it's still showing up in running configuration...... It's on 2960 switch running 12.2 lanbasek9 IOS.
... View more
Labels:
07-24-2013
08:22 AM
Hi Folks, we've 2 nexus 7k with vPC feature on. A server having 4 NICs, 2 on each Nexus. But nexus interface state is becoming "suspended" again & again. Could there be order of operation issue? fast response would be appreciated
... View more
Labels:
07-23-2013
10:16 AM
Daniela, internal router just can't have the "O IA" routes i.e. inter-area routes in ospf, you'll see them in ABR/ASBR either you misconfigured the hostname, i mean, not as per the exact topology; or it just bug with simulator. also, i couldn't open your .pkt file, coz i'm using in Win7 & you in linux, ubuntu I suggest you to do this in GNS3, that'll give almost live device experience, CPT is just a simulator, not a cisco IOS. But, GNS3 emulates original cisco IOS. reply me with your findings..
... View more
07-23-2013
07:50 AM
Areas doesn't have routing table, statement is misleading. Please tell, are checking on internal routers or ABR ? Sent from Cisco Technical Support Android App
... View more
07-23-2013
07:36 AM
Can we configure "COPP profile strict" on nexus 7k in live production network, can it cause any kind of interruption/outage in network? Sent from Cisco Technical Support Android App
... View more
Labels:
07-04-2013
08:45 AM
You are not getting ARP replies from PE, you don't have the full layer 2 connectivity, check with ISP. Sent from Cisco Technical Support Android App
... View more
06-25-2013
12:54 AM
Hi PIMv2 / IGMPv2 are best from configuration ease & administrative control point of view. Rest depends, if you have some specific thing to accomplish in your IPTV multicast enviroment & on your topology. Share the with us your design style, & might suggest you something better.
... View more
06-18-2013
07:01 AM
HI Kevin, there should be L2 connectivity between HSRP peers, which is missing over here. Plus, you can't make inter-work HSRP on router side & VRRP on firewall side. option 1: Get direct link betwwen CPE 1 & CPE 2 option 2: Use L2 switch & CPE1 & CPE2 via this for HSRP, VRRP; you have chosse one of the option & recommeded is option 2 (although it'd involve little more cost) but will in tshoot, if anything goes wroung. Cheers Ashok
... View more
06-18-2013
06:48 AM
Yeah Randal, I missed-out that speed thing, you won't be able to use ether-channel; But surely you can use EIGRP, for unequal-cost load balancing, if both cisco devices
... View more
06-16-2013
11:29 AM
okay..!! thats fine; what are make & model of router & switch you are using.... you migh be able to use ether-channel to load balance across both the lines, if your router does support for swithport configuration. below is link for Understanding the ether-channel:- http://www.cisco.com/en/US/tech/tk389/tk213/technologies_tech_note09186a0080094714.shtml For configurations:- http://www.cisco.com/en/US/docs/switches/lan/catalyst3550/software/release/12.1_13_ea1/configuration/guide/swethchl.html Cheers Ashok
... View more
06-15-2013
12:00 PM
HI Randal, What I understand from above; you want to upgrade your 100mbps link to 1000mbps ( 1 gig), which streched from Sw4948 to DC router, & Servers connected to Sw4989. In this, don't worry about IP address & all; they're nothing to do with link bandwidth. just go ahead & replace the link, server must be having static IP(just confirm it). Chees Ashok
... View more
06-05-2013
01:13 AM
Hi Steven, Well, what I'm suggesting could be configurational task, but why don't you run VRRP after connecting new device, & make new device Master, later on , if you want, can remove the the VRRP config as well. Cheers Ashok
... View more
06-04-2013
06:35 AM
Okay.. you want do it on Hub location, based on the remote site IP subnet classification..!!!.....Any particular reason of deploying shaping in this way; I mean what 's goal you want achieve via this, that could help me suggest you better. Cheers Ashok
... View more
05-21-2014
Hmm..... That's not the case.... Tried this already Even I've seen its
kinda default command in some...
07-24-2013
Hi Folks,we've 2 nexus 7k with vPC feature on. A server having 4 NICs, 2
on each Nexus. But nexus in...
07-23-2013
Daniela, internal router just can't have the "O IA" routes i.e.
inter-area routes in ospf, you'll se...
07-23-2013
Areas doesn't have routing table, statement is misleading.Please tell,
are checking on internal rout...
07-23-2013
Can we configure "COPP profile strict" on nexus 7k in live production
network, can it cause any kind...
07-04-2013
You are not getting ARP replies from PE, you don't have the full layer 2
connectivity, check with IS...
06-25-2013
Hi PIMv2 / IGMPv2 are best from configuration ease & administrative
control point of view. Rest depe...
06-18-2013
HI Kevin,there should be L2 connectivity between HSRP peers, which is
missing over here.Plus, you ca...
06-18-2013
Yeah Randal,I missed-out that speed thing, you won't be able to use
ether-channel;But surely you can...
06-16-2013
okay..!! thats fine; what are make & model of router & switch you are
using.... you migh be able to ...
06-15-2013
HI Randal,What I understand from above; you want to upgrade your 100mbps
link to 1000mbps ( 1 gig), ...
06-05-2013
Hi Steven, Well, what I'm suggesting could be configurational task, but
why don't you run VRRP after...
Public Statistics
| Date Registered | 06-01-2013 01:30 AM |
| Date Last Visited | 08-18-2017 04:03 AM |
| Total Messages Posted | 29 |
| Total Helpful Votes Received | 5 |
.jpg "VIP Advisor"){kind=icon}
