About Lynn Hedspeth

Lynn Hedspeth · 02-24-2017

We had an outage last week that turned out to be the fault of out service provider. But it caused us to do some testing of the the Subscriber server to make sure it would take over in the event of a Publisher failure. Turns out it the Subscriber will...

Lynn Hedspeth · 02-17-2017

Publisher CM works fine, but when the Subscriber takes over there is no access to outside lines from the 2921 Voice Router. The Subscriber CM is syncing with the Publisher CM OK. CM 8.5 2921 Voice Router at site. 2 PRI Lines, plus 5 pots lines in th...

Lynn Hedspeth · 07-03-2013

We currently have department that has multible FXO ports sent to a Hunt Pilot, and it is working fine.I would like to change it to it being directed to a single extension, then the single extension being routed to the Hunt Pilot. Then final destinati...

Lynn Hedspeth · 05-03-2013

We need calls coming into main reception which is part of a Line Group that rings Top Down to 4 other extensions, and if not answered ends up back at the call handler for the main reception. I have it all working except we need to Call Forward All ca...

Lynn Hedspeth · 04-04-2013

We have 4 remote sites all with 2901 routers, and a mixture of 7962's, 7942's, and 6911's. I have less than 20 devices setup in separate common device pools for each site. The 7962's, and 7942's register flawlessly when the network is interrupted bac...

Lynn Hedspeth · 02-27-2017

No POTS is involved. I added 2 "dial-peer voice # voip" commands to the Voice Router (2921) config. They were added to point the voice router to the subscriber CallManager Server. Which was not taking over in the event of a Publisher failure. Unfor...

Lynn Hedspeth · 02-17-2017

Inbound and Outbound both are dead on the PRI lines. Everything is fine when the Publisher CM is up. I didn't mention this in my original post, but I am not sure about the pots lines. They are all routed outside our building. I will have to wait unti...

Lynn Hedspeth · 07-04-2013

I had it working by a workaround I thought of this morning. I changed the number that is sent to a 4 digit random number that is passed by the original "dial-peer voice 1 voip". Then added a translation pattern in the CUCM to send the new 4 digit "70...

Lynn Hedspeth · 07-03-2013

I greatly appreciate your help, and advise.I copied dial-peer 1 as suggested, edited the dial-peer name, and the destination-pattern tothe commands below. dial-peer voice 3 voip preference 1 destination-pattern 180400 session target ipv4:172.25.180.1...

Lynn Hedspeth · 07-03-2013

voice-port 0/1/3 is the one I am testing, but once it is working I will need to make the same changes to 2 other ports.voice-port 0/1/0 and 0/1/3 will eventually need to have the same destination.I removed the dial-peer entry I made earlier after it ...

Member Since	‎12-06-2012 10:54 AM
Date Last Visited	‎08-18-2017 04:03 AM
Posts	15

User Statistics

User Activity

Dial Peer issues not routing a single translation pattern. 200+ others work after adding 2 dial pears for voip routing to Publisher, and Subscriber CallManager servers.

Call Manager 8.5 Subscriber can't access outside lines from 2921 Voice Router

Incoming call to ext# from FXO port

CFA on Ext. in Line Group called by Hunt Pilot?

6911's won't register in SRST Fallback mode

No POTS is involved.

Inbound and Outbound on the

Re: Incoming call to ext# from FXO port

Incoming call to ext# from FXO port

Re: Incoming call to ext# from FXO port