Cisco Community
English
Register
Great changes are coming to Cisco Community in July. LEARN MORE
Register
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
somethinglesspersonal
‎05-08-2019

Beginner
Recent Badges
Awards
Recent Badges
See all
1 Accepted Solution
1 Helpful Vote
20 Replies
10 Replies
5 Replies
Stats
Member since ‎07-17-2013
48
Posts
5
Helpful
2
Solutions

Re: SG500X Stack / Standalone - Unable to change IPV4 Address.

Created by in Small Business Switches
05-07-2019
05-07-2019
This is unreal. Yet another person out there in complete disbelief. I AM JUST GOING TO RESET THIS @#...

SG250-10P Cannot assign Static IP address

Created by in Switching
05-01-2018
05-01-2018
I log in, go to IP Configuration --> IPv4 Interface, click the one and only VLAN1 to select it, then...

Re: No DHCP from VLAN unless AP plugged directly into Meraki MX64

Created by in Switching
04-27-2018
04-27-2018
Well, I am both embarrassed and ecstatic. That was it. Just had to configure the uplink port on the ...

Re: No DHCP from VLAN unless AP plugged directly into Meraki MX64

Created by in Switching
04-27-2018
04-27-2018
OMG. I'll be right back. I just realized I never made any VLAN changes on the uplink port on the swi...

No DHCP from VLAN unless AP plugged directly into Meraki MX64

Created by in Switching
04-27-2018
04-27-2018
Hello, I've been running into issues getting a single VLAN setup for guest wifi. My hardware:Meraki ...

Re: CVE-2018-0101 vulnerability

Created by in Network Security
03-07-2018
03-07-2018
Thanks for the replies everyone. This actually makes it much easier to do what I wanted anyway -- sw...

CVE-2018-0101 vulnerability

Created by in Network Security
03-06-2018
03-06-2018
I am basically coming here to see if anyone else, not a very big expert in Cisco, has found somethin...

Re: Upgrade Cisco ASA from 8.2(4) to 9.1.7.20 or later

Created by in Network Security
02-12-2018
02-12-2018
Hello there. I'm in the same boat. I have two Cisco ASA 5510's connected via persistent IPSEC tunnel...

For me, it was this: https:/

Created by in Routing
10-21-2015
10-21-2015
For me, it was this: https://supportforums.cisco.com/discussion/12627556/error-opening-ike-port-4500...

Well, not only is this

Created by in VPN
10-21-2015
10-21-2015
Well, not only is this embarrassing, but very, very hard to believe. After running "sh xlate" and se...

Error opening IKE port 4500 on Interface outside

Created by in VPN
10-09-2015
10-09-2015
Brand new Cisco ASA 5506-X. Ran the VPN wizard. At the end, all is "OK" except an error: Error: cryp...

Hi Karsten, can you provide

Created by in Routing
10-08-2015
10-08-2015
Hi Karsten, can you provide the CLI to accomplish your suggestion? Also, the reason I never use CLI ...

Any resolution? I'm having

Created by in Routing
10-08-2015
10-08-2015
Any resolution? I'm having the same issue. Brand new ASA 5506-X out of the box running ASA version 9...

It ended up being a user

Created by in Switching
03-17-2015
03-17-2015
It ended up being a user error on my end. I was trying to configure DHCP relay on the wrong interfac...

How to prevent ASDM desktop shortcut manifestation

Created by in Network Security
07-22-2014
07-22-2014
I have three ASDM shortcuts on my desktop. I'm sure you know where this is going. I move the shortcu...
Public Statistics
Date Registered ‎07-17-2013 09:00 AM
Date Last Visited ‎05-08-2019 12:01 AM
Total Messages Posted 48
Total Helpful Votes Received 5
Helpful Votes Given To
See all >
Helpful Votes From
See all >