About Knowlesy14

Knowlesy14 · 08-19-2019

I'm testing using Prime Infrastructure 3.5 to push out a new IOS to some Cat3850 switches. I have a Linux VM running SCP server acting as the intermediary. The job starts and I see the IOS file start to copy to the Linux SCP folder. Then job fails an...

Knowlesy14 · 11-26-2018

I'm integrating a pilot installation of CUCM 11.5 with a production Avaya environment and am having trouble figuring out how to get the Caller ID to show when calling from Avaya to Cisco extensions (works going in to opposite direction). Calls from...

Knowlesy14 · 08-07-2018

I'm trying to register a SX80 via the Webex Control Hub (admin.webex.com). (Add device, generate 16-digit activation code). However, when I go to enter the activation code I get the error 'The activation service requires an encryption option key'. ...

Knowlesy14 · 06-01-2018

Hi, I haven't been able to find any other documentation/posts regarding this issue. I'm setting up an SX80 codec with a Telepresence SpeakerTrack 60. I've connected all components as directed but the microphone array is not being detected. Am I mis...

Knowlesy14 · 05-15-2018

Hi! I'm upgrading a UC environment from 11.0 to 11.5. One of the pre-upgrade tasks is to ensure the subnet mask is in the recommended format for /24. "If you are using a 24-bit IP subnet mask, ensure that you use the following format:255.255.255....

Knowlesy14 · 08-20-2019

I have had success using Prime to upgrade IOS versions in the past but have always thoroughly tested before using in production. It's only since transitioning to IOS 16.x that this appears to have become an issue. Back to the good ol' manual method. ...

Knowlesy14 · 08-20-2019

Thanks, yes I've tried tinkering with using different ciphers to no avail, unfortunately. I'm not putting any further effort into this... Not overly impressed with Prime.

Knowlesy14 · 08-19-2019

Hello and thanks! I was able to verify the MD5 checksums are the same at both locations. Looking at the logs of the target 3850 switch I'm seeing the error: %SSH-3-BAD_PACK_LEN: Bad packet length 1349676916 Quick search of that error and came across...

Knowlesy14 · 11-27-2018

Yes, there's no reference to ext 1707 in the SIP messages. 'Anonymous'@10.19.120.178 (Sonus Gateway) instead though, which I'm assuming means that info is being restricted/stripped off by Avaya prior to being sent out the SIP trunk since CUCM isn't s...

Knowlesy14 · 11-27-2018

Thanks, I'll take a look at that doc.... I collected a call trace (attached) for an Avaya phone (ext 1707) calling Cisco phone (ext 1205). Caller ID is displayed as 'Private' on the Cisco phone. I'd like to change this to show the calling extension...

Member Since	‎10-13-2017 10:35 AM
Date Last Visited	‎08-21-2019 05:09 AM
Posts	18

User Statistics

User Activity

Cisco Prime 3.5 - Software Image Distribution Fails - File checksum/size on destination varies from file checksum/size of source. Probable Cause: The file copy failed due to Temporary Network errors..

Avaya to CUCM ext - Caller ID = 'Private'

Unable to register SX80 to Webex Control hub - 'The activation service requires an encryption option key'

SX80 with SpeakerTrack 60 microphone array not detected.

UC upgrade 11.0 to 11.5 -cannot change subnet mask format as directed by documentation.

Re: Cisco Prime 3.5 - Software Image Distribution Fails - File checksum/size on destination varies from file checksum/size of source. Probable Cause: The file copy failed due to Temporary Network errors..

Re: Cisco Prime 3.5 - Software Image Distribution Fails - File checksum/size on destination varies from file checksum/size of source. Probable Cause: The file copy failed due to Temporary Network errors..

Re: Cisco Prime 3.5 - Software Image Distribution Fails - File checksum/size on destination varies from file checksum/size of source. Probable Cause: The file copy failed due to Temporary Network errors..

Re: Avaya to CUCM ext - Caller ID = 'Private'

Re: Avaya to CUCM ext - Caller ID = 'Private'