About ilicveselin

ilicveselin · 05-19-2016

Hi, I am unable to find what parameters influence serial number. The problem is that virtual TPS is dynamically loaded into VM inventory and every time it gets different serial number even if I have static IP, Mask, Default Gateway, MAC, NTP, speed, ...

ilicveselin · 11-16-2013

Hi,From the following guide there is a sentence that clearly states that DVO feature is supported on CME systems. http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmecti.html#wp1217063"The CTI CSTA Protocol Suite in Cisco...

ilicveselin · 07-03-2011

Hello everybody,I am integrating two CUP 8.0 servers via interclustering peers. Both of these two servers works OK with their local CUPC users. Addition of users or IM between users occurs normal within same CUP server. I was able to add Intercluster...

ilicveselin · 06-22-2011

I know that RS232 in DMP system is for sending control messages to LCD screen. On this DMP, I see that RS232 is in the form of 2.5mm jack.http://www.cisco.com/en/US/prod/collateral/video/ps9339/ps7220/data_sheet_c78-625677.htmlCan anybody tels me wha...

ilicveselin · 06-22-2011

Hello,When I dial CUC pilot number, I hear "Cisco Unity Connection messaging system. From a touchtone telephone you can dial extension at any time. For directory of extensions, please press 4..."Problem is when I try to dial number 1001 or try to pre...

ilicveselin · 11-20-2013

In another words...Have this configuration below regarding cti/csta any influence on behaviour of Cicso Jabber for Android/iOS registered to CME?voice service voip allow-connections sip to sip no supplementary-service sip moved-temporarily no su...

ilicveselin · 07-12-2011

Hi christos, thansk for your effort.I have checked once again all configuration, and havent found error.Recreated intercluster peers on both servers, without success...Get some intercluster sync agent and XCP router traces again, and cant found what ...

ilicveselin · 07-07-2011

Hi Christos,thansk for answer, and sorry for late reply. I followed this document:http://www.cisco.com/en/US/docs/voice_ip_comm/cups/8_0/english/install_upgrade/deployment/guide/dgintercluster.pdf•The intercluster peers must each integrate with a dif...

ilicveselin · 07-06-2011

Hi Christos,thanks for answer. To make sure that traces are set to detailed, I performed addition of user in both directions:- In 11h:04m on CUP-2 server user marija@pod.com tried to add user user veselin@pod.com located at CUP-1 server- After 3 minu...

ilicveselin · 07-05-2011

Hi Christos, thanks for answer. I run this command from CLI and result is 't'.Also, I collected trace from CUP-1 and CUP-2 servers. In this trace example user from CUP-1 is trying to add user from CUP-2. It seems that CUP-1 not sending subscribe to C...

Member Since	‎12-24-2008 02:19 AM
Date Last Visited	‎07-11-2024 11:43 PM
Posts	22

User Statistics

User Activity

Virtual Telepresence Server - parameters that influence serial number

DVO feature in CME?

Adding contact from intercluster CUPC server failed

Difference between RS232 9-pin and jack

Unity Connection 8.0.3 - Opening Greeting ignores user input

DVO feature in CME?

Re: Adding contact from intercluster CUPC server failed

Re: Adding contact from intercluster CUPC server failed

Re: Adding contact from intercluster CUPC server failed

Re: Adding contact from intercluster CUPC server failed