About Ditter

Ditter · 04-12-2024

Hi to all,i am facing a strange issue with poe devices on a Cat 4500 with SUP7L and the WS-X4648-RJ45V+E card.When we disconnect a poe device from the switch and we plug int again , the device gets in power deny state.And if we plug this device to a...

Ditter · 03-11-2024

Hi ,i have already implemented site to site VPNs for which there was no need for extra licensing.But now i would like to ask if in order to implement Remote Access VPNs do i need extra licenses to buy?And this is true either for SSL or IPSec Remote A...

Ditter · 03-10-2024

Hi to all,i would like to share with you a "worrying" behavior of FMC.To be more specific, i noticed that a week ago , FMC stopped sending emails for some events i had configured it.At the beginning i assumed that it was a problem on the relay agent ...

Ditter · 02-28-2024

Hi to all.i have enabled in the second 40G slot of a 9407 with SUP1 a huawei 40G interface as in the png attached.The switch does not seem to have understood that. It rus 17.06.04.Chassis Type: C9407RMod Ports Card Type Model Serial No.---+-----+----...

Ditter · 02-19-2024

Hi, never found why i can not ping outside marked interfaces on FTD device although via platform settings this is open.Please refer to the attached screeshot.Thanks,Ditter.

Ditter · 04-15-2024

Found the problem!UPoE supports only 24 ports @ 60W for a maximux power supply of 1440 WAll the excess APs fall in power deny state. Changed supply to 30W and everything came back to life!Thank you @Leo Laohoo and @Georg Pauwen for your support.

Ditter · 04-15-2024

We are plugging Huawei AirEngine 6760-X1 in a WS-X4748-UPOE card in a Catalyst 4500 with SUP-7L.The problem was created when a previously working AP was removed from its port and changed position with another identical one. The technicians wanted to...

Ditter · 04-15-2024

Hi Leo,used the logging event command you proposed and i was able to catch the following logging message:ILPOWER-5-ILPOWER_POWER_DENY: Interface Gi2/10: inline power denied. Reason: Requested power(16211) exceeds interface or module capability.That i...

Ditter · 04-14-2024

Hi Leo,no meaning to enable cdp on this port as there is no cisco equipment there. Instead lldp is enabled as it is third party equipment (third party WiFi) .But i did wht you proposed (both cdp enable as well as remove bpdu guard) but nothing chang...

Ditter · 04-13-2024

Hi Leo ,in order to bounce the port i have to send a colleague of mine to do so as the switch in not in our premises.The port config is as follows:interface GigabitEthernet2/10switchport access vlan 9switchport mode accessswitchport port-security max...

Member Since	‎07-03-2018 02:53 AM
Date Last Visited	‎04-17-2024 11:48 PM
Posts	256
Total Helpful Votes Received	41

User Statistics

User Activity

Catalyst 4500 with SUP7L deny power to poe ports

Do i need anyconnect licenses for Remote Access VPNs

FMC showed a strange behavior

Huawei 40G LR Interface with Cisco 9407 with 17.06.04

Unable to ping outside interfaces on FTDs (IOS 7.2.5)

Re: Catalyst 4500 with SUP7L deny power to poe ports

Re: Catalyst 4500 with SUP7L deny power to poe ports

Re: Catalyst 4500 with SUP7L deny power to poe ports

Re: Catalyst 4500 with SUP7L deny power to poe ports

Re: Catalyst 4500 with SUP7L deny power to poe ports