About dcgtechnologies

dcgtechnologies · 04-29-2022

I have a 3750G switch that is booting, but is booting up garbage when it boots up. I can not boot to prompt or even configure the switch. I was working before I turned it off and used it at another site. Now I have a switch that turns on and fully bo...

dcgtechnologies · 11-29-2021

I have two different VLan's for this Access Point. I have a switch port 47 on a 3750X POE Switch configured per below: interface GigabitEthernet1/0/47switchport access vlan 10switchport trunk encapsulation dot1qswitchport trunk native vlan 10switchpo...

dcgtechnologies · 10-26-2019

Hello All,Long time forum user here. I have a Cisco 3802i with three SSID's on it. At random times all SSID's can drop and all connected devices fall off the network. The only way I know to fix it is unplug the AP and plug it back in and then all SSI...

dcgtechnologies · 03-20-2019

I copied the configuration from my 3750G to my new 3750X on GigabitEthernet1/0/1-48, which is the exact configuration on my 3750G and I had a hard time trying to figure out why it would not work, but after some long time troubleshooting I found out t...

dcgtechnologies · 03-19-2019

Hello,I am trying to figure out if it is possible to copy the config from a Cisco 3750G 24 Port to a Cisco 3750X 48-Port Switch. This is for a switch replacement. Does anyone know the proper steps to get this done? I understand you can can use a TFTP...

dcgtechnologies · 11-30-2021

That is perfect, but the only thing I had to do was to put a line back in and fix the native vlan. See below;interface GigabitEthernet1/0/47switchport access vlan 10 - This needed to be added back in to access the gateway on VLAN10switchport trunk en...

dcgtechnologies · 03-20-2019

I did the re-number and used the "no switch 3 provision" command and it removed it.

dcgtechnologies · 03-20-2019

So I did the renumber from 3 to 1 and it all came up on stack as number 1 but the configuration for GigabitInterface 3/0/1 is still there. I had to renumber back to Stack 3 to get it to work again. How do I remove that part of the config as my second...

dcgtechnologies · 03-20-2019

I see where you guys are coming from. It has a label of 3 in the stack and I do not use the stack configuration so I will re-number it. Will I lose my configuration if I re-number it and the configuration is on GigabitEthernet1 already? Thank you.

dcgtechnologies · 03-19-2019

So I got it up and running but, I am wondering why I have two sets of Gigabitethernet Interfaces on this switch. They are GigabitEthernet1/0/1-48 and GigabitEthernet3/0/1-48. I had to configure GigabitEthernet3/0/1 in order to get everything to work....

Member Since	‎12-10-2014 08:04 PM
Date Last Visited	‎05-06-2022 12:04 AM
Posts	55

User Statistics

User Activity

3750G Switch Booting Issue

Aironet 1040 WAP Issue

Cisco 3802i SSID's all Dropping at random times all at once

Issue with a 3750XPOE after copying configuration

Copy config from Cisco 3750G 24-Port to Cisco 3750X 48-Port Switch

Re: Aironet 1040 WAP Issue

Re: Issue with a 3750XPOE after copying configuration

Re: Issue with a 3750XPOE after copying configuration

Re: Issue with a 3750XPOE after copying configuration

Re: Copy config from Cisco 3750G 24-Port to Cisco 3750X 48-Port Switch