Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Nevy
Stats
Member since
09-07-2018
8
Posts
0
Helpful
0
Solutions
Created by
Nevy
in Unified Computing System Discussions
in Unified Computing System Discussions
10-23-2018
08:08 AM
10-23-2018
08:08 AM
Hi Robert, the Guide above is for UCSM (Manager) . I use UCS Central 2.0 (1c) to manage all our 4 UCS domains. So it make sense to configure disjointed L2 Networking using UCS Central Software. Do You know how to configure disjointed L2 Network in UCS Central? Thanks and best regards Nevzat
... View more
Created by
Nevy
in Unified Computing System Discussions
in Unified Computing System Discussions
10-11-2018
04:28 AM
10-11-2018
04:28 AM
Thank you very much ! I think it is better and professional to assignVLANs to the desired port channel. Best regards nevzat
... View more
Created by
Nevy
in Unified Computing System Discussions
in Unified Computing System Discussions
10-11-2018
04:13 AM
10-11-2018
04:13 AM
Hi Robert, Thank You for your answer. That is what I'm looking for. On page 1 under Note "..By default, data traffic in Cisco UCS works on a principle of mutual inclusion. All traffic for all VLANs and upstream networks travels along all uplink ports and port channels. If you have upgraded from a release that does not support upstream disjoint layer-2 networks, you must assign the appropriate uplink interfaces to your VLANs, or traffic for those VLANs continues to flow along all uplink ports and port channels..." That means, usually I needn't to configure somesthing additional as all traffic travels along all port channels...Our first release was 3.x, I think it supports upstream disjoint layer-2 Networks. Best regards Nevzat
... View more
Created by
Nevy
in Unified Computing System Discussions
in Unified Computing System Discussions
10-11-2018
03:08 AM
10-11-2018
03:08 AM
Good morning,
we have some UCS Domains administered by UCS Central2.0(1c). We have configured 2 new additional Uplink Ports and created in each FI a new Port Channel (nr 2). After that we have created new vLAN. My question is for my understanding or how to configure the next steps: How can should I configure the new vLAN / vNIC to take traffic through the new created Channel Port?e.g.If I assign to Service Profile Template the new vNIC template (with new created vLAN) the Server will have additional NIC for a new Network. The NIC or vNIC Or VLAN shoul be combined with the new created Port Channel, or shouldn't be? May be I have less knowledge about Routing or how is the Networking process in UCS .
Thanks in advance.
Best regards
Nevzat
... View more
Labels:
Created by
Nevy
in Unified Computing System Discussions
in Unified Computing System Discussions
09-10-2018
12:57 AM
09-10-2018
12:57 AM
Hi Niko,
Thank You for your reply.
Regards
Nevzat
... View more
Created by
Nevy
in Unified Computing System Discussions
in Unified Computing System Discussions
09-10-2018
12:53 AM
09-10-2018
12:53 AM
Hi Kirk,
Thanks for your reply. The security issue with TLS1.0 is known and because of the PCI requirement it has to be disabled any communication which uses this protocol. Its a pity that vendors do not take this security point seriously. I hope the next release (patch) is available asap.
Regards
Nevzat
... View more
Created by
Nevy
in Unified Computing System Discussions
in Unified Computing System Discussions
09-07-2018
01:53 AM
09-07-2018
01:53 AM
Hello,
we are running the FW 3.1(1g)A and UCSM Version 3.1(1g). As we can not disable TLS1.0 as shown in the UCS_Admin_Mgmt_Guide_3_1_chapter_0110.html we want to upgrade to 3.2.(3). Is it OK if I only upgrade Infrastructure FW to this Version or Do I have to update Blade FW as well?
Many thanks and best regards
Nevzat
... View more
- Tags:
- UCSM firmware
Labels:
Created by
Nevy
in Unified Computing System Discussions
in Unified Computing System Discussions
09-07-2018
01:36 AM
09-07-2018
01:36 AM
Hello, I've to disable the protocol vTLS1.0 in UCS Central 2.0(1c). I could not find any documents or commands for that issue. Do you know how to disable it?
Thank You!
Best regards
nevzat
... View more
- Tags:
- tls
- UCS Central
Labels:
10-23-2018
Hi Robert, the Guide above is for UCSM (Manager) . I use UCS Central 2.0
(1c) to manage all our 4 UC...
10-11-2018
Thank you very much ! I think it is better and professional to
assignVLANs to the desired port chann...
10-11-2018
Hi Robert, Thank You for your answer. That is what I'm looking for. On
page 1 under Note "..By defau...
Created by
Nevy
in Unified Computing System Discussions
10-11-2018
10-11-2018
Good morning, we have some UCS Domains administered by UCS
Central2.0(1c). We have configured 2 new ...
Created by
Nevy
in Unified Computing System Discussions
09-10-2018
09-10-2018
Hi Niko, Thank You for your reply. Regards Nevzat
Created by
Nevy
in Unified Computing System Discussions
09-10-2018
09-10-2018
Hi Kirk, Thanks for your reply. The security issue with TLS1.0 is known
and because of the PCI requi...
Created by
Nevy
in Unified Computing System Discussions
09-07-2018
09-07-2018
Hello, we are running the FW 3.1(1g)A and UCSM Version 3.1(1g). As we
can not disable TLS1.0 as show...
Created by
Nevy
in Unified Computing System Discussions
09-07-2018
09-07-2018
Hello, I've to disable the protocol vTLS1.0 in UCS Central 2.0(1c). I
could not find any documents o...
Public Statistics
| Date Registered | 09-07-2018 01:21 AM |
| Date Last Visited | 04-03-2019 01:29 AM |
| Total Messages Posted | 8 |
