About Hans Martinez

Hans Martinez · 06-15-2023

Hi community, I'm working on implementing EEM on a Cisco ASR9K; I need to be able to determine by syslog when a track changes UP/DOWN status. When I add the lines of "event manager environment" the system only leaves the last one of "environment". I ...

Hans Martinez · 06-13-2023

Hi Community, I'm trying to install DNAC on appliance DN2-HW-APL with reference the "Cisco DNA Center Second-Generation Appliance Installation Guide, Release 2.1.2". https://www.cisco.com/c/en/us/td/docs/cloud-systems-management/network-automation-an...

Hans Martinez · 02-28-2023

Hi, anyone how can help to me and validate or recommend a topology to implemente a cluster of CNR for DHCP on failover pair; using a second Nic to that redundancy service? Topology one: It's posible implement a failover-pair if de IP address on seco...

Hans Martinez · 11-03-2022

Hi, I'm working to migrate an ASA to FTD, when I run Migration Tool it's ignore esmtp inspection set on the global policy. Can I configure that policy manually on the FTD or realy is not necessary? !access-list esmtp extended deny tcp host 10.16.8.19...

Hans Martinez · 11-02-2022

Hi; I have two FMC 2500 on HA; planning upgrade from 6.4.0-13 to 6.6.1-91. My process: 1 backup. 2 check ntp and space on disk. 3 upload file on active and standby 4 pause HA synchronization 5 run readiness on both devices, active and standby 6 updat...

Hans Martinez · 06-15-2023

Solved event manager environment _syslog_pattern1 .*(track 6 state Track_Up)event manager environment _syslog_pattern2 .*(track 6 state Track_Down)

Hans Martinez · 06-15-2023

Hi Preston; I'm going to proceed with open a TAC case; thank you by your support and time.

Hans Martinez · 10-20-2022

Hi Marvin, the version 6.6.1 because the minimum release to integrate some new devices, but you are right 6.6.7 is a better option to upgrade; and in this moment 7.0.4 can wait because we have another device on 6.2.3 but need to do other priorities n...

Hans Martinez · 10-20-2022

Hi BB; thank you by your suppport, I did a Lab of upgrade. Lab 1: FMC 6.4.0.13-57 >>> 6.6.0-90; successful. Lab 2: FMC 6.4.0.13-57 >>> 6.6.1-91, successful. I'm goning to go by the LAB2 on real environment. Thanks a lot.

Hans Martinez · 01-11-2019

Hi Andrea, thank you for your support. Yes I was saw the doc Nexus 9000 TCAM Carving before as reference in other post. I decide get out 512 of RACL to set later at PACL, I used 512 to PACL because is de default value on Nexus 93120. The confi...

Member Since	‎04-19-2011 04:37 PM
Date Last Visited	‎02-14-2024 12:05 AM
Posts	24

User Statistics

User Activity

EEM - ASR9K - EEM Scritp of Multiple line of event manager environment

DNA CENTER 2.1.2 INSTALLATION PROCEDURE / INSTALL LOOP / NIC ISSUES

CPNR 10 / Best topology to deploy a failover on pair local servers

ASA to FTD+FMC / Migration Tool 3.0 / inspect on global service policy

FMC 2500 HA / 6.4.0-13 / readiness don't start on standby device.

Re: EEM - ASR9K - EEM Scritp of Multiple line of event manager environ

Re: DNA CENTER 2.1.2 INSTALLATION PROCEDURE / INSTALL LOOP / NIC ISSUE

Re: FMC 2500 / Upgrade from 6.4.0.13 to 6.6.1 / Correct Path to do

Re: FMC 2500 / Upgrade from 6.4.0.13 to 6.6.1 / Correct Path to do

Re: Nexus9000 93180YC-EX - NXOS 7.0(3)I6(1) - PACL Resources