Ok. Thank you. I got an invalid input detected. I'm to run the show running-config to see what changes took I2V-OBE(config)# I2V-OBE(config)#$ce static tcp 192.168.200.11 22 interface Vlan30 2222 I2V-OBE(config)#$ce static tcp 192.168.200.11 8080 interface Vlan30 8080 I2V-OBE(config)#$de source list NAT_ACL interface Cellular1/0 overload I2V-OBE(config)#$ce static tcp 192.168.200.11 8443 interface Vlan30 8443 I2V-OBE(config)#$ce static tcp 192.168.200.11 8085 interface Vlan30 8085 I2V-OBE(config)#$ce static tcp 192.168.200.11 5001 interface Cellular0/0 5001 I2V-OBE(config)#$ce static tcp 192.168.200.11 8484 interface Vlan30 8484 I2V-OBE(config)#$ce static tcp 192.168.200.11 8081 interface Vlan30 8081 I2V-OBE(config)#$ce static udp 192.168.200.11 44444 interface Vlan30 44444 I2V-OBE(config)#$ce static tcp 192.168.11.120 80 interface Vlan30 8123 I2V-OBE(config)#ip route 0.0.0.0 0.0.0.0 Cellular1/0 overload ^ % Invalid input detected at '^' marker. I2V-OBE(config)#no ip route 0.0.0.0 0.0.0.0 dhcp I2V-OBE(config)# I2V-OBE(config)#no dialer watch-list 1 ip 5.6.7.8 0.0.0.0 ^ % Invalid input detected at '^' marker. I2V-OBE(config)#no dialer watch-list 1 delay route-check initial 60 ... View more

I had trouble implementing the following changes:    ip dns server --> no ip nat inside source static tcp 192.168.200.11 22 interface Vlan30 2222 --> no ip nat inside source static tcp 192.168.200.11 8080 interface Vlan30 8080 ip nat inside source list NAT_ACL interface Cellular1/0 overload --> no ip nat inside source static tcp 192.168.200.11 8443 interface Vlan30 8443 --> no ip nat inside source static tcp 192.168.200.11 8085 interface Vlan30 8085 --> no ip nat inside source static tcp 192.168.200.11 5001 interface Cellular0/0 5001 --> no ip nat inside source static tcp 192.168.200.11 8484 interface Vlan30 8484 --> no ip nat inside source static tcp 192.168.200.11 8081 interface Vlan30 8081 --> no ip nat inside source static udp 192.168.200.11 44444 interface Vlan30 44444 --> no ip nat inside source static tcp 192.168.11.120 80 interface Vlan30 8123 --> ip route 0.0.0.0 0.0.0.0 Cellular1/0 overload --> no ip route 0.0.0.0 0.0.0.0 dhcp ip ssh rekey time 60 ip ssh rekey volume 1048576 ip scp server enable ! ip access-list standard NAT_ACL permit 192.168.0.0 0.0.255.255 permit 172.20.1.0 0.0.0.255 permit 172.29.1.0 0.0.0.255 ! --> no dialer watch-list 1 ip 5.6.7.8 0.0.0.0 --> no dialer watch-list 1 delay route-check initial 60 --> no dialer watch-list 1 delay connect 1 dialer-list 1 protocol ip permit dialer-list 1 protocol ipv6 permit ipv6 ioam timestamp   How would you make those changes in the terminal?   I made the other changes, saved config using do wr, then I re-ran show ip interface brief and no ip address was assigned to Cellular 1/0 ... View more

Thanks for your continued support.    I'm not sure what a chat-script is. To get the config, I ran show running-config on the router.  Is that the right command to get the file?   Regards to the profiles, Profile 1 should data and Profile 3 should the attach-profile, I think. According to:      https://www.cisco.com/c/en/us/td/docs/routers/access/800/829/software/configuration/guide/b_IR800config/b_cellular.html ... View more

Hi Georg, attached is my config and below are my cellular profiles:   I2V-OBE#show cellular 1/0 profile Profile 1 = INACTIVE * ** -------- PDP Type = IPv4v6 Access Point Name (APN) = vzwims Authentication = None Profile 2 = INACTIVE -------- PDP Type = IPv4v6 Access Point Name (APN) = vzwadmin Authentication = None Profile 3 = INACTIVE -------- PDP Type = IPv4v6 Access Point Name (APN) = VZWINTERNET Authentication = None Profile 4 = INACTIVE -------- PDP Type = IPv4v6 Access Point Name (APN) = vzwapp Authentication = None Profile 5 = INACTIVE -------- PDP Type = IPv4v6 Access Point Name (APN) = vzw800 Authentication = None Profile 6 = INACTIVE -------- PDP Type = IPv4v6 Access Point Name (APN) = vzwclass6 Authentication = None * - Default profile ** - LTE attach profile     Please let me know if you need more info ... View more