About Muhammad H. Usmani

Muhammad H. Usmani · 10-28-2019

Hi All, I am using a Cisco 3560 Switch and I have observed that "show clock" displays the correct time as mine but when I check logs, it shows the time 5 Hours behind me. It can be considered as the switch is showing time related to GMT timezone as w...

Muhammad H. Usmani · 09-15-2019

Hi all, How do i select the IOS in flash amongst the three in Cisco Catalyst 4948E Switch. I have set the boot flash of that particular IOS but whenever switch restart it loads the 1st one in auto. Kindly help in changing the priority of IOS / Flash ...

Muhammad H. Usmani · 03-13-2019

Hi all, For a few days I have been observing vlan1 to be flapping between 2 ports of two 3750E switches (2 ports on each switch) which are cross connected to each other. Out of these 2 ports on each switch, one is that cross connectivity port. Stats ...

Muhammad H. Usmani · 02-09-2019

I have cisco 3750X switch and from past few days I have been observing the below mentioned error. Feb 9 17:10:11: %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not respondingFeb 9 17:15:29: %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is no...

Muhammad H. Usmani · 02-07-2019

I have been observing this error extensively on my standalone switch. Feb 8 07:13:51.708: %PLATFORM_STACKPOWER-4-CABLE_B_CURRENT_OUT: Switch 1 stack power cable 2 outward current is over the limitFeb 8 07:14:51.829: %PLATFORM_STACKPOWER-4-CABLE_B_CUR...

Muhammad H. Usmani · 10-28-2019

Switch#show clock14:22:51.046 PKT Mon Oct 28 2019 Switch#show run | in clockclock timezone PKT 5 0 NTP is not enabled Switch#show versionCisco IOS Software, C3560 Software (C3560-IPBASEK9-M), Version 15.0(2)SE11, RELEASE SOFTWARE (fc3)Technical Supp...

Muhammad H. Usmani · 03-25-2019

@mario.jost Basically I have connected 3 switches (3rd switch was not a part of discussion but as you mentioned the connectivity so they are connected as follows) Switch A Gi1/0/25 --------> Switch B Gi1/0/12Switch A Gi1/0/26 & Switch B Gi1/0/9 ----...

Muhammad H. Usmani · 03-22-2019

@Leo Laohoo I mentioned earlier too that I am observing this error on 2 switches, both switches are showing the same behaviour on the ports where I have laid the cables for cross connecting both of these switches. Find the descriptions and mac addr...

Muhammad H. Usmani · 03-20-2019

@Leo Laohoo Please find below the stats as requested Switch#sh mac addr int gi1/0/26Mac Address Table-------------------------------------------Vlan Mac Address Type Ports---- ----------- -------- ----- Switch#sh mac addr int gi1/0/25Mac Address T...

Muhammad H. Usmani · 03-13-2019

1st Switch: Gi1/0/12 up up "CROSS CONNECTIVITY WITH NEW SWITCH" interface GigabitEthernet1/0/12description "CROSS CONNECTIVITY WITH NEW SWITCH"switchport mode dynamic desirableload-interval 30no cdp enable 2nd Switch: Gi1/0/25 up up "CROSS CONNECTIVI...

Member Since	‎02-06-2019 03:24 AM
Date Last Visited	‎08-02-2023 12:02 AM
Posts	19

User Statistics

User Activity

Service TimeStamps Command Not Working

Choose IOS amongs the three stored in Flash of Switch

%SW_MATM-4-MACFLAP_NOTIF: Host 286e.d422.926d in vlan 1 is flapping between port Gi1/0/12 and port Gi1/0/9

PLATFORM_ENV-1-FRU_PS_ACCESS

STACKPOWER-4-CABLE_B_CURRENT_OUT

Re: Service TimeStamps Command Not Working

Re: %SW_MATM-4-MACFLAP_NOTIF: Host 286e.d422.926d in vlan 1 is flapping between port Gi1/0/12 and port Gi1/0/9

Re: %SW_MATM-4-MACFLAP_NOTIF: Host 286e.d422.926d in vlan 1 is flapping between port Gi1/0/12 and port Gi1/0/9

Re: %SW_MATM-4-MACFLAP_NOTIF: Host 286e.d422.926d in vlan 1 is flapping between port Gi1/0/12 and port Gi1/0/9

Re: %SW_MATM-4-MACFLAP_NOTIF: Host 286e.d422.926d in vlan 1 is flapping between port Gi1/0/12 and port Gi1/0/9