Here are the configs   Router1(our side) interface Loopback0 ip address 1.1.1.1 255.255.255.0 ! interface FastEthernet0/0 ip address 192.168.1.1 255.255.255.0 shutdown duplex auto speed auto ! interface FastEthernet0/1 ip address 103.255.126.253 255.255.255.0 duplex auto speed auto vrrp 1 description F1 vrrp 1 ip 103.255.126.111 ! interface Serial1/0 no ip address shutdown serial restart-delay 0 ! interface Serial1/1 ip address 182.93.88.62 255.255.255.0 serial restart-delay 0 ! interface Serial1/2 no ip address shutdown serial restart-delay 0 ! interface Serial1/3 no ip address shutdown serial restart-delay 0 ! router bgp 13092 no synchronization bgp log-neighbor-changes network 103.233.182.0 mask 255.255.255.0 network 103.255.126.0 mask 255.255.255.0 neighbor 2.2.2.2 remote-as 13092 neighbor 2.2.2.2 update-source Loopback0 neighbor 2.2.2.2 next-hop-self neighbor 2.2.2.2 route-map SUBISU-IN in neighbor 182.93.88.61 remote-as 4007 neighbor 182.93.88.61 route-map SUBISU-IN in neighbor 182.93.88.61 route-map SUBISU-OUT out no auto-summary ! ip forward-protocol nd ip route 2.2.2.0 255.255.255.0 103.255.126.250 ip route 103.233.182.0 255.255.255.0 FastEthernet0/1 ! ! no ip http server no ip http secure-server ! ! ip prefix-list DEFAULT seq 5 permit 0.0.0.0/0 ! ip prefix-list P1 seq 5 permit 103.255.126.0/24 ! ip prefix-list P2 seq 5 permit 103.233.182.0/24 ! ! ! route-map SUBISU-IN permit 10 match ip address prefix-list DEFAULT ! route-map SUBISU-OUT permit 10 match ip address prefix-list P1 P2 !     Router2(our side) interface Loopback0 ip address 2.2.2.2 255.255.255.0 ! interface FastEthernet0/0 ip address 192.168.1.2 255.255.255.0 shutdown duplex auto speed auto ! interface FastEthernet0/1 ip address 103.255.126.250 255.255.255.0 duplex auto speed auto vrrp 1 description F1 vrrp 1 ip 103.255.126.111 vrrp 1 priority 90 ! interface Serial1/0 ip address 202.79.34.61 255.255.255.0 serial restart-delay 0 ! interface Serial1/1 no ip address shutdown serial restart-delay 0 ! interface Serial1/2 no ip address shutdown serial restart-delay 0 ! interface Serial1/3 no ip address shutdown serial restart-delay 0 ! router bgp 13092 no synchronization bgp log-neighbor-changes network 103.233.182.0 mask 255.255.255.0 network 103.255.126.0 mask 255.255.255.0 neighbor 1.1.1.1 remote-as 13092 neighbor 1.1.1.1 update-source Loopback0 neighbor 1.1.1.1 next-hop-self neighbor 202.79.34.1 remote-as 17501 neighbor 202.79.34.1 route-map WLINK-IN in neighbor 202.79.34.1 route-map WLINK-OUT out no auto-summary ! ip forward-protocol nd ip route 1.1.1.0 255.255.255.0 103.255.126.253 ip route 103.233.182.0 255.255.255.0 FastEthernet0/1 ! ! ip http server no ip http secure-server ! ! ip prefix-list DEFAULT seq 5 permit 0.0.0.0/0 ! ip prefix-list P1 seq 5 permit 103.255.126.0/24 ! ip prefix-list P2 seq 5 permit 103.233.182.0/24 ! ! ! route-map WLINK-OUT permit 10 match ip address prefix-list P1 P2 ! route-map WLINK-IN permit 5 match ip address prefix-list DEFAULT ! ! ##ignore the fast 0/0 interface in both routers## ## the isp are just sending the default route towards us.##   I have attached image for show ip bgp  output for both routers, what i want to do is I want prefix P1 to take the ebgp route via the vrrp master router, but another prefix P2 to take the ibgp path to our 2nd router and then go to another ISP.(outbound).   Its been quite some time I am trying to figure this out. Hope someone can help.           ... View more

thanks for your time in this, BUT I want some prefix to go to the vrrp master router then that specific prefix should take the ibgp path to the vrrp slave router and then to the isp? Can you suggest some options to achieve this.   In both of our internal routing tables, there will be a default route from isp and ibgp, (route from isp always preferred)   ... View more

is there any method using route-map and not community? ... View more

my vrrp backup router also stuck in init state.   I have a switch in between the two routers any idea? ... View more