Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Ali Hazim
Stats
Member since
02-27-2019
22
Posts
0
Helpful
1
Solution
10-12-2019
08:19 AM
Hi, Is There Any Scenario To Use The "Permanent" Parameter At The End Of a Static Route Command ip route .... permanent
... View more
Labels:
10-12-2019
08:08 AM
Thank You Very Much, You've Answered My Question And Gave Something New To Read About Which Is (Shaping)
... View more
10-12-2019
02:15 AM
Hi, Is There a Way To Specify Different Bandwidth Size Of Sub-Interfaces, For Example: If I Had A G0/0 Interface, And I Created 3 Sub-Interfaces G0/0.1, G0/0.2, & G0/0.3. Is There a Way That I Can Manage The Bandwidth So That G0/0.1 = 600Mbps, G0/0.2 & G0/0.3 = 200Mbps Each?
... View more
Labels:
09-05-2019
05:18 PM
Thanks For Your Reply, But This Is What Confuses Me, Why a Dynamic Desirable Interface Be Configured With Port Security?
... View more
09-05-2019
12:41 AM
This Is The Error I'm Getting, Also This Is Mentioned In Cisco's Official Get Cert And All Over The Internet, But I Haven't Seen Any Explanation To Why It's Rejected.
... View more
09-04-2019
11:16 PM
Hi, Why Can't Port-Security Be Configured On a Dynamic Desirable Interface (Default), Why Must The Interface Be Configured As Access Or Trunk, I Can't See The Relation Between Port-Security And VLAN, Shouldn't I Be Able To Configure Port-Security Without Changing The Default VLAN Configuration Of an Interface? Thank You In Advance.
... View more
Labels:
06-29-2019
02:02 AM
I've Found The Solution. To Enable The IPv6 Features, The Following Command Must Be Used In The Global Config. Mode: (config)# sdm prefer dual-ipv4-and-ipv6 routing
... View more
06-26-2019
12:42 AM
Hi Everyone, I Have a C3560 Switch With an IPService Image, I'm Trying To Configure OSPFv3 But I Can't Find Any IPv6 Related Commands, I've Used The Cisco Feature Navigator To See If OSPFv3 Is Available For My Image And It Says That It Does, So What's The Problem Here.
... View more
Labels:
05-06-2019
07:51 AM
Hi All, When Configuring a Sub-Interface In a Router, The Number That Can Be Assigned To It Will Be Within The Range (0 - 4294967296), Which Means That The Range Is Represented By a 32 Bits, So My Questions Are: 1- Where Are Those 32 Bits (Ethernet Header, IP Header, Or Some Sort Of Registry)? 2- The Range Is Waaaay To Big For a Real Case Scenario, Since Sub-Interfaces Are Used To Create a Router On a Stick To Provide Connectivity Between Different VLANs, And Since There Are Only 4096 VLNAs, Shouldn't The Number Of Sub-Interfaces Be No More Than (4096)? Thanks In Advance
... View more
Labels:
03-13-2019
01:23 PM
Thank You For Your Response, But My Question Is Why a Port That Is Configured Statically As Trunk Doesn't Automatically Disable DTP Like Access Ports Do
... View more
03-13-2019
11:42 AM
When Manually Configuring a Port As Access, DTP Will Be Automatically Disabled. So Why Is It When Configuring a Port As Trunk, DTP Will Still Be Enabled?
... View more
Labels:
03-10-2019
09:08 AM
Hi All, In a Redundant Topology, How Does VTP Avoid Loops When Sending Its Summary Advertisement
... View more
Labels:
03-10-2019
01:57 AM
Hi In The Topology Shown, Both PCs Are In VLAN1, The Link Between The Switches Is Configured As Trunk Allowing Only VLANs 10-100, & SW1 Is a VTP Server, SW2 Is a VTP Client. The Two PCs Can't Ping Each Other (Obviously Because The VLAN1 Is Not Allowed On The Trunk). My Question Is, Why Does VTP Works Fine Even Though The Native VLAN Is Not Allowed On The Trunk?
... View more
Labels:
03-06-2019
05:16 AM
Hi All What Made Cisco Work On The ISL Encapsulation Protocol When The IEEE 802.1Q Protocol Was Efficient? What Advantage Does The ISL Has Over The IEEE 802.1Q?
... View more
Labels:
10-12-2019
Hi,Is There Any Scenario To Use The "Permanent" Parameter At The End Of
a Static Route Command ip ro...
10-12-2019
Thank You Very Much, You've Answered My Question And Gave Something New
To Read About Which Is (Shap...
10-12-2019
Hi,Is There a Way To Specify Different Bandwidth Size Of Sub-Interfaces,
For Example:If I Had A G0/0...
09-05-2019
Thanks For Your Reply, But This Is What Confuses Me, Why a Dynamic
Desirable Interface Be Configured...
09-05-2019
This Is The Error I'm Getting, Also This Is Mentioned In Cisco's
Official Get Cert And All Over The ...
09-04-2019
Hi,Why Can't Port-Security Be Configured On a Dynamic Desirable
Interface (Default), Why Must The In...
06-29-2019
I've Found The Solution.To Enable The IPv6 Features, The Following
Command Must Be Used In The Globa...
06-26-2019
Hi Everyone, I Have a C3560 Switch With an IPService Image, I'm Trying
To Configure OSPFv3 But I Can...
05-06-2019
Hi All,When Configuring a Sub-Interface In a Router, The Number That Can
Be Assigned To It Will Be W...
03-13-2019
Thank You For Your Response, But My Question Is Why a Port That Is
Configured Statically As Trunk Do...
03-13-2019
When Manually Configuring a Port As Access, DTP Will Be Automatically
Disabled. So Why Is It When Co...
03-10-2019
Hi All,In a Redundant Topology, How Does VTP Avoid Loops When Sending
Its Summary Advertisement
03-10-2019
Hi In The Topology Shown, Both PCs Are In VLAN1, The Link Between The
Switches Is Configured As Trun...
Public Statistics
| Date Registered | 02-27-2019 11:16 AM |
| Date Last Visited | 10-12-2019 11:34 AM |
| Total Messages Posted | 22 |
Helpful Votes Given To
| User | Helpful Count |
|---|---|
| 10 | |
| 5 | |
| 20 | |
| 5 | |
| 5 |
.jpg "VIP Mentor"){kind=icon}
.jpg "Hall of Fame Expert"){kind=icon}
