Rick, thanks again, I appreciate everything.   Thanks, Dave ... View more

Rick,   Thanks again....you helped another issue that I wasn't going to bother you with but it also allowed my wireless clients to start connecting when I plugged my AP in!   Here is the output of show run an show ip int Lab_2921#show run Building configuration... Current configuration : 2018 bytes ! ! Last configuration change at 12:36:32 EST Thu Mar 28 2019 by davidstriplin ! NVRAM config last updated at 12:36:39 EST Thu Mar 28 2019 by davidstriplin ! version 15.7 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Lab_2921 ! boot-start-marker boot-end-marker ! ! ! no aaa new-model clock timezone EST -5 0 ! ! ! ! ! ! ! ! ! ip dhcp excluded-address 10.0.1.170 ip dhcp excluded-address 10.0.1.100 10.0.1.254 ip dhcp excluded-address 10.0.1.1 ! ip dhcp pool Inside DHCP network 10.0.1.0 255.255.255.0 dns-server 75.75.75.75 75.75.76.76 default-router 10.0.1.1 ! ! ip dhcp class any ! ! no ip domain lookup ip cef no ipv6 cef ! multilink bundle-name authenticated ! ! ! ! license udi pid CISCO2921/K9 sn FTX1728AHR1 ! ! username davidstriplin secret 5 $1$j5Ka$6u.mf3wInjRpFMZ2PRLxY. ! redundancy ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Embedded-Service-Engine0/0 no ip address shutdown ! interface GigabitEthernet0/0 description Facing The ISP (WAN) ip address dhcp ip nat outside ip virtual-reassembly in duplex auto speed auto ! interface GigabitEthernet0/1 description Facing The LAN (LAN) ip address 10.0.1.1 255.255.255.0 ip nat inside ip virtual-reassembly in duplex auto speed auto ! interface GigabitEthernet0/2 no ip address shutdown duplex auto speed auto ! ip default-gateway 10.0.1.1 ip forward-protocol nd ! no ip http server no ip http secure-server ! ip dns server ip nat inside source list 1 interface GigabitEthernet0/0 overload ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/0 dhcp ip ssh time-out 60 ! ! ! access-list 1 permit 10.0.1.0 0.0.0.255 access-list 102 permit ip 10.0.1.0 0.0.0.255 any ! control-plane ! ! vstack ! line con 0 logout-warning 120 login local line aux 0 line 2 no activation-character no exec transport preferred none transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1 line vty 0 4 login local transport input ssh ! scheduler allocate 20000 1000 ! end   Lab_2921#show ip int Embedded-Service-Engine0/0 is administratively down, line protocol is down Internet protocol processing disabled GigabitEthernet0/0 is up, line protocol is up Internet address is 69.180.36.8/23 Broadcast address is 255.255.255.255 Address determined by DHCP MTU is 1500 bytes Helper address is not set Directed broadcast forwarding is disabled Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is enabled IP CEF switching turbo vector IP multicast fast switching is enabled IP multicast distributed fast switching is disabled IP route-cache flags are Fast, CEF Router Discovery is disabled IP output packet accounting is disabled IP access violation accounting is disabled TCP/IP header compression is disabled RTP/IP header compression is disabled Policy routing is disabled Network address translation is enabled, interface in domain outside BGP Policy Mapping is disabled Input features: Common Flow Table, Stateful Inspection, Virtual Fragment Reassembly, Virtual Fragment Reassembly After IPSec Decryption, NAT Outside, MCI Check Output features: Post-routing NAT Outside, Common Flow Table, Stateful Inspection, NAT ALG proxy IPv4 WCCP Redirect outbound is disabled IPv4 WCCP Redirect inbound is disabled IPv4 WCCP Redirect exclude is disabled GigabitEthernet0/1 is up, line protocol is up Internet address is 10.0.1.1/24 Broadcast address is 255.255.255.255 Address determined by setup command MTU is 1500 bytes Helper address is not set Directed broadcast forwarding is disabled Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is enabled IP CEF switching turbo vector IP multicast fast switching is enabled IP multicast distributed fast switching is disabled IP route-cache flags are Fast, CEF Router Discovery is disabled IP output packet accounting is disabled IP access violation accounting is disabled TCP/IP header compression is disabled RTP/IP header compression is disabled Policy routing is disabled Network address translation is enabled, interface in domain inside BGP Policy Mapping is disabled Input features: Common Flow Table, Stateful Inspection, Virtual Fragment Reassembly, Virtual Fragment Reassembly After IPSec Decryption, MCI Check Output features: NAT Inside, Common Flow Table, Stateful Inspection, NAT ALG proxy IPv4 WCCP Redirect outbound is disabled IPv4 WCCP Redirect inbound is disabled IPv4 WCCP Redirect exclude is disabled GigabitEthernet0/2 is administratively down, line protocol is down Internet protocol processing disabled NVI0 is up, line protocol is up Internet address will be negotiated using IPCP Broadcast address is 255.255.255.255 MTU is 1514 bytes Helper address is not set Directed broadcast forwarding is disabled Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is disabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is disabled IP Null turbo vector IP Null turbo vector IP multicast fast switching is enabled IP multicast distributed fast switching is disabled IP route-cache flags are Fast, CEF Router Discovery is disabled IP output packet accounting is disabled IP access violation accounting is disabled TCP/IP header compression is disabled RTP/IP header compression is disabled Policy routing is disabled Network address translation is disabled BGP Policy Mapping is disabled Input features: MCI Check Output features: Post-routing NAT NVI Output IPv4 WCCP Redirect outbound is disabled IPv4 WCCP Redirect inbound is disabled IPv4 WCCP Redirect exclude is disabled ... View more

Rick,   Done as requested.  Here is the output of show run to confirm.   Lab_2921#show dhcp pool InsideDHCP ^ % Invalid input detected at '^' marker. Lab_2921#show ip dhcp pool Pool Inside DHCP : Utilization mark (high/low) : 100 / 0 Subnet size (first/next) : 0 / 0 Total addresses : 254 Leased addresses : 9 Pending event : none 1 subnet is currently in the pool : Current index IP address range Leased addresses 10.0.1.19 10.0.1.1 - 10.0.1.254 9 Lab_2921# Lab_2921# Lab_2921#show ip int Embedded-Service-Engine0/0 is administratively down, line protocol is down Internet protocol processing disabled GigabitEthernet0/0 is up, line protocol is up Internet address is 69.180.36.8/23 Broadcast address is 255.255.255.255 Address determined by DHCP MTU is 1500 bytes Helper address is not set Directed broadcast forwarding is disabled Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is disabled IP Null turbo vector IP multicast fast switching is enabled IP multicast distributed fast switching is disabled IP route-cache flags are Fast, No CEF Router Discovery is disabled IP output packet accounting is disabled IP access violation accounting is disabled TCP/IP header compression is disabled RTP/IP header compression is disabled Policy routing is disabled Network address translation is enabled, interface in domain outside BGP Policy Mapping is disabled Input features: Common Flow Table, Stateful Inspection, Virtual Fragment Reassembly, Virtual Fragment Reassembly After IPSec Decryption, NAT Outside, MCI Check Output features: Post-routing NAT Outside, Common Flow Table, Stateful Inspection, NAT ALG proxy IPv4 WCCP Redirect outbound is disabled IPv4 WCCP Redirect inbound is disabled IPv4 WCCP Redirect exclude is disabled GigabitEthernet0/1 is up, line protocol is up Internet address is 10.0.1.1/24 Broadcast address is 255.255.255.255 Address determined by setup command MTU is 1500 bytes Helper address is not set Directed broadcast forwarding is disabled Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is enabled IP CEF switching turbo vector IP multicast fast switching is enabled IP multicast distributed fast switching is disabled IP route-cache flags are Fast, CEF Router Discovery is disabled IP output packet accounting is disabled IP access violation accounting is disabled TCP/IP header compression is disabled RTP/IP header compression is disabled Policy routing is disabled Network address translation is enabled, interface in domain inside BGP Policy Mapping is disabled Input features: Common Flow Table, Stateful Inspection, Virtual Fragment Reassembly, Virtual Fragment Reassembly After IPSec Decryption, MCI Check Output features: NAT Inside, Common Flow Table, Stateful Inspection, NAT ALG proxy IPv4 WCCP Redirect outbound is disabled IPv4 WCCP Redirect inbound is disabled IPv4 WCCP Redirect exclude is disabled GigabitEthernet0/2 is administratively down, line protocol is down Internet protocol processing disabled NVI0 is up, line protocol is up Internet address will be negotiated using IPCP Broadcast address is 255.255.255.255 MTU is 1514 bytes Helper address is not set Directed broadcast forwarding is disabled Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is disabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is disabled IP Null turbo vector IP Null turbo vector IP multicast fast switching is enabled IP multicast distributed fast switching is disabled IP route-cache flags are Fast, CEF Router Discovery is disabled IP output packet accounting is disabled IP access violation accounting is disabled TCP/IP header compression is disabled RTP/IP header compression is disabled Policy routing is disabled Network address translation is disabled BGP Policy Mapping is disabled Input features: MCI Check Output features: Post-routing NAT NVI Output IPv4 WCCP Redirect outbound is disabled IPv4 WCCP Redirect inbound is disabled IPv4 WCCP Redirect exclude is disabled   Lab_2921(config)#int gig0/0 Lab_2921(config-if)#ip route-cache Lab_2921(config-if)#exit Lab_2921(config)#exit Lab_2921#cop Mar 28 15:30:59.779: %SYS-5-CONFIG_I: Configured from console by davidstriplin o n console Lab_2921#copy run Lab_2921#copy running-config st Lab_2921#copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] Lab_2921#co Lab_2921#cop Lab_2921#copy ru Lab_2921#copy running-config tftp Address or name of remote host []? Lab 2921 Config_WORKING_ 3-28-2019 ?Invalid host address or name %Error parsing filename (Invalid IP address or hostname) Lab_2921#copy running-config tftp Address or name of remote host []? 10.0.1.3 Destination filename [lab_2921-confg]? Lab 2921 Config_WORKING_ 3-28-2019 !! 1996 bytes copied in 0.256 secs (7797 bytes/sec) Lab_2921#copy Lab_2921#copy r Lab_2921#copy ru Lab_2921#copy running-config st Lab_2921#copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] Lab_2921#show run Building configuration... Current configuration : 1996 bytes ! ! Last configuration change at 10:30:59 EST Thu Mar 28 2019 by davidstriplin ! NVRAM config last updated at 10:32:53 EST Thu Mar 28 2019 by davidstriplin ! version 15.7 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Lab_2921 ! boot-start-marker boot-end-marker ! ! ! no aaa new-model clock timezone EST -5 0 ! ! ! ! ! ! ! ! ! ip dhcp excluded-address 10.0.1.170 ip dhcp excluded-address 10.0.1.100 10.0.1.254 ip dhcp excluded-address 10.0.1.1 ! ip dhcp pool Inside DHCP network 10.0.1.0 255.255.255.0 dns-server 75.75.75.75 75.75.76.76 ! ! ip dhcp class any ! ! no ip domain lookup ip cef no ipv6 cef ! multilink bundle-name authenticated ! ! ! ! license udi pid CISCO2921/K9 sn FTX1728AHR1 ! ! username davidstriplin secret 5 $1$j5Ka$6u.mf3wInjRpFMZ2PRLxY. ! redundancy ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Embedded-Service-Engine0/0 no ip address shutdown ! interface GigabitEthernet0/0 description Facing The ISP (WAN) ip address dhcp ip nat outside ip virtual-reassembly in no ip route-cache cef duplex auto speed auto ! interface GigabitEthernet0/1 description Facing The LAN (LAN) ip address 10.0.1.1 255.255.255.0 ip nat inside ip virtual-reassembly in duplex auto speed auto ! interface GigabitEthernet0/2 no ip address shutdown duplex auto speed auto ! ip default-gateway 10.0.1.1 ip forward-protocol nd ! no ip http server no ip http secure-server ! ip dns server ip nat inside source list 1 interface GigabitEthernet0/0 overload ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/0 dhcp ! ! ! access-list 1 permit 10.0.1.0 0.0.0.255 access-list 102 permit ip 10.0.1.0 0.0.0.255 any ! control-plane ! ! vstack ! line con 0 logout-warning 120 login local line aux 0 line 2 no activation-character no exec transport preferred none transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1 line vty 0 4 login local transport input ssh ! scheduler allocate 20000 1000 ! end ... View more

And we are good to go!  I am currently writing this using the configuration that you helped me create and I'm browsing on the internet through the Cisco router hooked directly to my PC!!!!!!!!     Seriously, I want to sincerely thank you for taking time out of your day and helping me so much, it is greatly appreciated!     Just for grins....here is the current show run and show ip int so you can see if everything else looks good.   Lab_2921#show ip int br Interface IP-Address OK? Method Status Protocol Embedded-Service-Engine0/0 unassigned YES unset administratively down down GigabitEthernet0/0 69.180.36.8 YES DHCP up up GigabitEthernet0/1 10.0.1.1 YES manual up up GigabitEthernet0/2 unassigned YES unset administratively down down NVI0 unassigned YES unset up up Lab_2921#show ip int Embedded-Service-Engine0/0 is administratively down, line protocol is down Internet protocol processing disabled GigabitEthernet0/0 is up, line protocol is up Internet address is 69.180.36.8/23 Broadcast address is 255.255.255.255 Address determined by DHCP MTU is 1500 bytes Helper address is not set Directed broadcast forwarding is disabled Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is disabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is disabled IP Null turbo vector IP multicast fast switching is disabled IP multicast distributed fast switching is disabled IP route-cache flags are No CEF Router Discovery is disabled IP output packet accounting is disabled IP access violation accounting is disabled TCP/IP header compression is disabled RTP/IP header compression is disabled Policy routing is disabled Network address translation is enabled, interface in domain outside BGP Policy Mapping is disabled Input features: Common Flow Table, Stateful Inspection, Virtual Fragment Reassembly, Virtual Fragment Reassembly After IPSec Decryption, NAT Outside, MCI Check Output features: Post-routing NAT Outside, Common Flow Table, Stateful Inspection, NAT ALG proxy IPv4 WCCP Redirect outbound is disabled IPv4 WCCP Redirect inbound is disabled IPv4 WCCP Redirect exclude is disabled GigabitEthernet0/1 is up, line protocol is up Internet address is 10.0.1.1/24 Broadcast address is 255.255.255.255 Address determined by setup command MTU is 1500 bytes Helper address is not set Directed broadcast forwarding is disabled Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is enabled IP CEF switching turbo vector IP multicast fast switching is enabled IP multicast distributed fast switching is disabled IP route-cache flags are Fast, CEF Router Discovery is disabled IP output packet accounting is disabled IP access violation accounting is disabled TCP/IP header compression is disabled RTP/IP header compression is disabled Policy routing is disabled Network address translation is enabled, interface in domain inside BGP Policy Mapping is disabled Input features: Common Flow Table, Stateful Inspection, Virtual Fragment Reassembly, Virtual Fragment Reassembly After IPSec Decryption, MCI Check Output features: NAT Inside, Common Flow Table, Stateful Inspection, NAT ALG proxy IPv4 WCCP Redirect outbound is disabled IPv4 WCCP Redirect inbound is disabled IPv4 WCCP Redirect exclude is disabled GigabitEthernet0/2 is administratively down, line protocol is down Internet protocol processing disabled NVI0 is up, line protocol is up Internet address will be negotiated using IPCP Broadcast address is 255.255.255.255 MTU is 1514 bytes Helper address is not set Directed broadcast forwarding is disabled Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is disabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is disabled IP Null turbo vector IP Null turbo vector IP multicast fast switching is enabled IP multicast distributed fast switching is disabled IP route-cache flags are Fast, CEF Router Discovery is disabled IP output packet accounting is disabled IP access violation accounting is disabled TCP/IP header compression is disabled RTP/IP header compression is disabled Policy routing is disabled Network address translation is disabled BGP Policy Mapping is disabled Input features: MCI Check Output features: Post-routing NAT NVI Output IPv4 WCCP Redirect outbound is disabled IPv4 WCCP Redirect inbound is disabled IPv4 WCCP Redirect exclude is disabled Lab_2921# Lab_2921#show run Building configuration... Current configuration : 1993 bytes ! ! Last configuration change at 09:33:53 EST Thu Mar 28 2019 by davidstriplin ! NVRAM config last updated at 09:26:26 EST Thu Mar 28 2019 by davidstriplin ! version 15.7 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Lab_2921 ! boot-start-marker boot-end-marker ! ! ! no aaa new-model clock timezone EST -5 0 ! ! ! ! ! ! ! ! ! ip dhcp excluded-address 10.0.1.170 ip dhcp excluded-address 10.0.1.100 10.0.1.254 ip dhcp excluded-address 10.0.1.1 ! ip dhcp pool Inside DHCP network 10.0.1.0 255.255.255.0 dns-server 75.75.75.75 75.75.76.76 ! ! ip dhcp class any ! ! no ip domain lookup ip cef no ipv6 cef ! multilink bundle-name authenticated ! ! ! ! license udi pid CISCO2921/K9 sn FTX1728AHR1 ! ! username davidstriplin secret 5 $1$j5Ka$6u.mf3wInjRpFMZ2PRLxY. ! redundancy ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Embedded-Service-Engine0/0 no ip address shutdown ! interface GigabitEthernet0/0 description Facing The ISP (WAN) ip address dhcp ip nat outside ip virtual-reassembly in no ip route-cache duplex auto speed auto ! interface GigabitEthernet0/1 description Facing The LAN (LAN) ip address 10.0.1.1 255.255.255.0 ip nat inside ip virtual-reassembly in duplex auto speed auto ! interface GigabitEthernet0/2 no ip address shutdown duplex auto speed auto ! ip default-gateway 10.0.1.1 ip forward-protocol nd ! no ip http server no ip http secure-server ! ip dns server ip nat inside source list 1 interface GigabitEthernet0/0 overload ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/0 dhcp ! ! ! access-list 1 permit 10.0.1.0 0.0.0.255 access-list 102 permit ip 10.0.1.0 0.0.0.255 any ! control-plane ! ! vstack ! line con 0 logout-warning 120 login local line aux 0 line 2 no activation-character no exec transport preferred none transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1 line vty 0 4 login local transport input none ! scheduler allocate 20000 1000 ! end       ... View more

So I totally agree about the PC not picking up a default gateway, but I'm not sure how to get it to do so.  I've added a default-gateway to int gig0/1 as well as adding it to my DHCP pool, but as you can see it's still not picking it up....am I missing how to do so?  Here is the output of the PC as well as the show run and show ip int.   I feel like we are really close, but just need to close this out.  Thank you again so so much for your help!    h   Lab_2921>show run ^ % Invalid input detected at '^' marker. Lab_2921>ena Lab_2921#show run Building configuration... Current configuration : 1971 bytes ! ! Last configuration change at 09:02:51 EST Thu Mar 28 2019 by davidstriplin ! NVRAM config last updated at 08:32:13 EST Thu Mar 28 2019 by davidstriplin ! version 15.7 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Lab_2921 ! boot-start-marker boot-end-marker ! ! ! no aaa new-model clock timezone EST -5 0 ! ! ! ! ! ! ! ! ! ip dhcp excluded-address 10.0.1.170 ip dhcp excluded-address 10.0.1.100 10.0.1.254 ip dhcp excluded-address 10.0.1.1 ! ip dhcp pool Inside DHCP network 10.0.1.0 255.255.255.0 dns-server 8.8.8.8 8.8.4.4 ! ! ip dhcp class any ! ! no ip domain lookup ip cef no ipv6 cef ! multilink bundle-name authenticated ! ! ! ! license udi pid CISCO2921/K9 sn FTX1728AHR1 ! ! username davidstriplin secret 5 $1$j5Ka$6u.mf3wInjRpFMZ2PRLxY. ! redundancy ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Embedded-Service-Engine0/0 no ip address shutdown ! interface GigabitEthernet0/0 description Facing The ISP (WAN) ip address dhcp ip nat outside ip virtual-reassembly in no ip route-cache duplex auto speed auto ! interface GigabitEthernet0/1 description Facing The LAN (LAN) ip address 10.0.1.1 255.255.255.0 ip nat inside ip virtual-reassembly in duplex auto speed auto ! interface GigabitEthernet0/2 no ip address shutdown duplex auto speed auto ! ip default-gateway 10.0.1.1 ip forward-protocol nd ! no ip http server no ip http secure-server ! ip nat inside source list 1 interface GigabitEthernet0/0 overload ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/0 dhcp ! ! ! access-list 1 permit 10.0.1.0 0.0.0.255 access-list 102 permit ip 10.0.1.0 0.0.0.255 any ! control-plane ! ! vstack ! line con 0 logout-warning 120 login local line aux 0 line 2 no activation-character no exec transport preferred none transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1 line vty 0 4 login local transport input none ! scheduler allocate 20000 1000 ! end   Lab_2921>show ip dhcp pool Pool Inside DHCP : Utilization mark (high/low) : 100 / 0 Subnet size (first/next) : 0 / 0 Total addresses : 254 Leased addresses : 1 Pending event : none 1 subnet is currently in the pool : Current index IP address range Leased addresses 10.0.1.3 10.0.1.1 - 10.0.1.254 1 Lab_2921>show ip int gig0/1 GigabitEthernet0/1 is up, line protocol is up Internet address is 10.0.1.1/24 Broadcast address is 255.255.255.255 Address determined by setup command MTU is 1500 bytes Helper address is not set Directed broadcast forwarding is disabled Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is enabled IP CEF switching turbo vector IP multicast fast switching is enabled IP multicast distributed fast switching is disabled IP route-cache flags are Fast, CEF Router Discovery is disabled IP output packet accounting is disabled IP access violation accounting is disabled TCP/IP header compression is disabled RTP/IP header compression is disabled Policy routing is disabled Network address translation is enabled, interface in domain inside BGP Policy Mapping is disabled Input features: Common Flow Table, Stateful Inspection, Virtual Fragment Reassembly, Virtual Fragment Reassembly After IPSec Decryption, MCI Check Output features: NAT Inside, Common Flow Table, Stateful Inspection, NAT ALG proxy IPv4 WCCP Redirect outbound is disabled IPv4 WCCP Redirect inbound is disabled IPv4 WCCP Redirect exclude is disabled ... View more

Here is a better capture of the info if it helps.     Als   Also, here are the dumps of show ip int gig0/0 which I found interesting.....   Lab_2921#show ip int br Interface IP-Address OK? Method Status Protocol Embedded-Service-Engine0/0 unassigned YES unset administratively down down GigabitEthernet0/0 69.180.36.8 YES DHCP up up GigabitEthernet0/1 10.0.1.1 YES manual up up GigabitEthernet0/2 unassigned YES unset administratively down down NVI0 unassigned YES unset up up Lab_2921#show ip int gig0/0 GigabitEthernet0/0 is up, line protocol is up Internet address is 69.180.36.8/23 Broadcast address is 255.255.255.255 Address determined by DHCP MTU is 1500 bytes Helper address is not set Directed broadcast forwarding is disabled Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is disabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is disabled IP Null turbo vector IP multicast fast switching is disabled IP multicast distributed fast switching is disabled IP route-cache flags are No CEF Router Discovery is disabled IP output packet accounting is disabled IP access violation accounting is disabled TCP/IP header compression is disabled RTP/IP header compression is disabled Policy routing is disabled Network address translation is enabled, interface in domain outside BGP Policy Mapping is disabled Input features: Common Flow Table, Stateful Inspection, Virtual Fragment Reassembly, Virtual Fragment Reassembly After IPSec Decryption, NAT Outside, MCI Check Output features: Post-routing NAT Outside, Common Flow Table, Stateful Inspection, NAT ALG proxy IPv4 WCCP Redirect outbound is disabled IPv4 WCCP Redirect inbound is disabled IPv4 WCCP Redirect exclude is disabled ... View more

The address with 172.20.10.5 is the address my hotspot was giving when I connected it to my computer via usb to keep internet access while testing.  Please note, that when performing any tests, I would disable that network adapter so it didnt' cause any issues.  I apologize for sending the screenshot with both on there, I had taken two, and the one I didn't save only had the ethernet adapter that had the cable from the router.    So does that change your thoughts on this? ... View more

The address with 172.20.10.5 is the address my hotspot was giving when I connected it to my computer via usb to keep internet access while testing.  Please note, that when performing any tests, I would disable that network adapter so it didnt' cause any issues.  I apologize for sending the screenshot with both on there, I had taken two, and the one I didn't save only had the ethernet adapter that had the cable from the router.    So does that change your thoughts on this? ... View more

One thing I left off.... I was able to ping the Cisco router of 10.0.1.1 from my PC, but not the gateway of the ISP as you described earlier.  Don't know if that makes a difference to you or not... ... View more

Thank you again for the help!  Here is the output of the ARP-a commands.   I'v   I've also added the SHow Run to show I deleted the statement that you specificed.   Lab_2921#show run Building configuration... Current configuration : 1783 bytes ! ! Last configuration change at 19:25:43 UTC Wed Mar 27 2019 ! version 15.7 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Lab_2921 ! boot-start-marker boot-end-marker ! ! ! no aaa new-model ! ! ! ! ! ! ! ! ! ip dhcp excluded-address 10.0.1.170 ip dhcp excluded-address 10.0.1.100 10.0.1.254 ip dhcp excluded-address 10.0.1.1 ! ip dhcp pool Inside DHCP network 10.0.1.0 255.255.255.0 ! ip dhcp pool InsideDHCP ! ! ip dhcp class any ! ! no ip domain lookup ip cef no ipv6 cef ! multilink bundle-name authenticated ! ! ! ! license udi pid CISCO2921/K9 sn FTX1728AHR1 ! ! username davidstriplin secret 5 $1$j5Ka$6u.mf3wInjRpFMZ2PRLxY. ! redundancy ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! interface Embedded-Service-Engine0/0 no ip address shutdown ! interface GigabitEthernet0/0 description Facing The ISP (WAN) ip address dhcp ip nat outside ip virtual-reassembly in no ip route-cache duplex auto speed auto ! interface GigabitEthernet0/1 description Facing The LAN (LAN) ip address 10.0.1.1 255.255.255.0 ip nat inside ip virtual-reassembly in duplex auto speed auto ! interface GigabitEthernet0/2 no ip address shutdown duplex auto speed auto ! ip forward-protocol nd ! no ip http server no ip http secure-server ! ip nat inside source list 1 interface GigabitEthernet0/0 overload ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/0 dhcp ! ! ! access-list 1 permit 10.0.1.0 0.0.0.255 access-list 102 permit ip 10.0.1.0 0.0.0.255 any ! control-plane ! ! vstack ! line con 0 line aux 0 line 2 no activation-character no exec transport preferred none transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1 line vty 0 4 login transport input none ! scheduler allocate 20000 1000 ! end ... View more

Ok....so found a couple of issues.  When doing the ping testing, these three test failed with an error that I will post below.  Also, I copied all commands entered as well as the results for your review.  Please take a look and let me know your thoughts if you can.   Thanks again.... Lab_2921>show arp Protocol  Address          Age (min)  Hardware Addr   Type   Interface Internet  10.0.1.1                -   f872.ea8c.0ed1  ARPA   GigabitEthernet0/1 Internet  10.0.1.2                0   f430.b9cd.00b3  ARPA   GigabitEthernet0/1 Internet  69.180.36.1             0   0001.5c7d.2446  ARPA   GigabitEthernet0/0 Internet  69.180.36.8             -   f872.ea8c.0ed0  ARPA   GigabitEthernet0/0   Lab_2921>show ip route Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP        D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area        N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2        E1 - OSPF external type 1, E2 - OSPF external type 2        i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2        ia - IS-IS inter area, * - candidate default, U - per-user static route        o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP        a - application route        + - replicated route, % - next hop override, p - overrides from PfR   Gateway of last resort is 69.180.36.1 to network 0.0.0.0   S*    0.0.0.0/0 [1/0] via 69.180.36.1, GigabitEthernet0/0                 [1/0] via 69.180.36.1       10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks C        10.0.1.0/24 is directly connected, GigabitEthernet0/1 L        10.0.1.1/32 is directly connected, GigabitEthernet0/1       69.0.0.0/8 is variably subnetted, 2 subnets, 2 masks C        69.180.36.0/23 is directly connected, GigabitEthernet0/0 L        69.180.36.8/32 is directly connected, GigabitEthernet0/0       76.0.0.0/32 is subnetted, 1 subnets S        76.96.93.29 [254/0] via 69.180.36.1, GigabitEthernet0/0   Lab_2921>ping 69.180.36.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 69.180.36.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 8/12/20 ms   Ping transmit failures when doing ping from the command prompt of the PC on both .1 and .8 Ping transmit failures when doing ping from the command prompt of the PC on 8.8.8.8 ... View more

That is great advice.  Let me do the testing recommended and I will post results as well as any info that the tests show.  Stand by please....and thank you so much!   ... View more

Here are the outputs with everything in place...   Lab_2921#show arp Protocol  Address          Age (min)  Hardware Addr   Type   Interface Internet  10.0.1.1                -   f872.ea8c.0ed1  ARPA   GigabitEthernet0/1 Internet  10.0.1.2                0   f430.b9cd.00b3  ARPA   GigabitEthernet0/1 Internet  69.180.36.1             0   0001.5c7d.2446  ARPA   GigabitEthernet0/0 Internet  69.180.36.8             -   f872.ea8c.0ed0  ARPA   GigabitEthernet0/0                                                                                                                     Lab_2921#show ip int br Interface                  IP-Address      OK? Method Status                Protocol Embedded-Service-Engine0/0 unassigned      YES unset  administratively down down GigabitEthernet0/0         69.180.36.8     YES DHCP   up                    up GigabitEthernet0/1         10.0.1.1        YES manual up                    up GigabitEthernet0/2         unassigned      YES unset  administratively down down NVI0                       unassigned      YES unset  up                    up Lab_2921# ... View more

Hi,  Sorry I have to keep flip flopping my setup back and forth while testing.  Here is the outputs when things are connected.  I cleaned up what you specified, but I still don't have internet access.  Please see below.   Lab_2921#show arp Protocol  Address          Age (min)  Hardware Addr   Type   Interface Internet  10.0.1.1                -   f872.ea8c.0ed1  ARPA   GigabitEthernet0/1 Internet  10.0.1.2                0   f430.b9cd.00b3  ARPA   GigabitEthernet0/1 Lab_2921#     Lab_2921#show ip dhcp pool   Pool Inside DHCP :  Utilization mark (high/low)    : 100 / 0  Subnet size (first/next)       : 0 / 0  Total addresses                : 254  Leased addresses               : 1  Pending event                  : none  1 subnet is currently in the pool :  Current index        IP address range                    Leased addresses  10.0.1.3             10.0.1.1         - 10.0.1.254        1 Lab_2921#show ip int br Interface                  IP-Address      OK? Method Status                Protocol Embedded-Service-Engine0/0 unassigned      YES unset  administratively down down GigabitEthernet0/0         unassigned      YES DHCP   down                  down GigabitEthernet0/1         10.0.1.1        YES manual up                    up GigabitEthernet0/2         unassigned      YES unset  administratively down down NVI0                       unassigned      YES unset  up                    up Lab_2921#show arp Protocol  Address          Age (min)  Hardware Addr   Type   Interface Internet  10.0.1.1                -   f872.ea8c.0ed1  ARPA   GigabitEthernet0/1 Internet  10.0.1.2                0   f430.b9cd.00b3  ARPA   GigabitEthernet0/1 ... View more