About PeterTWJ13

PeterTWJ13 · 10-20-2019

Hi all,As I have firewall and L3 switches connected in an infrastructure.Cisco FirePOWER is configured with Global OSPF as VRF is not supported.Cisco Switch is configured both Global and VRF OSPF.Before the following hardening is performed, the routi...

PeterTWJ13 · 09-29-2019

Hi all,I am trying to configure OSPF between Cisco FirePower 2130 and Cisco 9300 Switch. Does the FirePower FDM supports OSPF Authentication Message Digest? If yes, how do I configure it?Please adviseThank YouPeter

PeterTWJ13 · 07-30-2019

Hi all,Previously, I have configured OSPF on ASA Firewall and is very similar to Cisco Routers and Switches.However, when I tried to configure OSPF on FirePOWER Firewall, the SmartCLI and FlexConfig looks pretty confusing.How do you relate the follow...

PeterTWJ13 · 06-19-2019

Hi all,While doing some simulation, I encountered some problems.L3 Switch (L3S1) is able to ping to the HSRP IP address and R2 G0/0/1 IP address. However, PC0 is unable to ping to the HSRP IP address and R2 G0/0/1 IP address.Did I missed out any conf...

PeterTWJ13 · 06-18-2019

Hi all,Based on the diagram below, I would like to achieve the following,- When SVR1 (VLAN10) need to communicate with SVR2 (VLAN20), it will have to go through S1 and ASA2- When SVR3 (VLAN10) need to communicate with SVR3 (VLAN20), it will have to g...

PeterTWJ13 · 09-29-2019

Hi Marvin,Thank you so much. Greatly appreciated.Peter

PeterTWJ13 · 09-29-2019

Hi Marvin,Do you have any example or picture to configure OSPF Authentication Message Digest and it's key inside the SmartCLI (OSPF or Interface session)?Please adviseThank YouPeter

PeterTWJ13 · 07-31-2019

Hi Marvin, 1. For the interface OSPF parameters, can I leave the parameters as default? 2. If the parameters are default and we have 7 sub-interfaces, can we apply the same template to all the sub-interfaces?Thank YouPeter

PeterTWJ13 · 07-31-2019

Hi Marvin,I just need to do the following command, but using SmartCLI and maybe FlexConfig if required.1. May I know how to do the following using SmartCLI and maybe FlexConfig?router ospf 1 log-adjacency-changes network 192.168.10.0 255.255.255.0 ...

PeterTWJ13 · 07-30-2019

Hi Marvin,I am managing the device locally using Firepower Device Manager (FDM) via the management LAN port. Software version is 6.3.0-83Please adviseThank YouPeter

Member Since	‎05-28-2019 11:49 PM
Date Last Visited	‎12-16-2019 11:54 PM
Posts	14

User Statistics

User Activity

OSPF Hardening for Cisco FIREPOWER Global OSPF and Cisco Switch VRF OSPF

Does Cisco FDM support OSPF Authentication Message Digest?

How to add OSPF route in FirePOWER

PC cannot ping HSRP IP and R2

ASA Firewall - OSPF Routing between different VLAN

Re: Does Cisco FDM support OSPF Authentication Message Digest?

Re: Does Cisco FDM support OSPF Authentication Message Digest?

Re: How to add OSPF route in FirePOWER

Re: How to add OSPF route in FirePOWER

Re: How to add OSPF route in FirePOWER