About Portus92

Portus92 · 03-04-2022

Hi,Is it possible to automatically set the agents back to ready state in Finesse when the jabber is back up and running after a "phone failure"?If not, is there a way to alert the agents that they are in a "not ready" state?We have UCCX in version 11...

Portus92 · 04-29-2021

Hi,I would like to be able to forward all incoming calls to a hunt pilot when there is a team meeting.I can't use CFNA because there are a lot of phones in the line group (all the rooms are not always open to unlog all phones). Do you have an idea?Th...

Portus92 · 07-24-2020

Hello,I would like to set up a site to site VPN between 2 Cisco 881 :version 15.5 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname RemoteLab ! boot-start-marker boot-...

Portus92 · 07-16-2020

Hi, The VPN connection is working but I am not able to ping a laptop in VLAN 10 (10.0.10.11) with the remote user (192.168.50.2).I can't ping the VPN user with the router. Interface: Dialer1 Username: uservpn Group: groupVPN Assigned address: 192.16...

Portus92 · 03-12-2020

Hi, I have a Cisco 897 VA.The WAN interface is connected to my pfSense (LAN 10.0.0.0/24, the pfSense address is 10.0.0.1).On my router, the WAN interface IP address is 10.0.0.90. I would like to have two VLAN (10 and 20) with an Internet access (wit...

Portus92 · 07-25-2020

Thank you !The config on RemoteLab is now : crypto map staticMap 5 ipsec-isakmp set peer AB.CD.160.216 set transform-set P2PSET match address 150 crypto map staticMap 10 ipsec-isakmp dynamic dynamicVPNAn I changed the tunnel mode on both : crypto ...

Portus92 · 07-16-2020

Thanks a lot ! access-list 100 deny ip 10.0.10.0 0.0.0.255 192.168.50.0 0.0.0.255 access-list 100 permit ip any anyIt works :)

Portus92 · 03-14-2020

There is nothing connected to GE0.The PC is connected to GE2. With ip nat it works, thanks ! I'm not sure I fully understand why. There is just one problem, I can't ping 10.0.10.1 or 10.0.10.11 from another PC.With the PC on GE2, I can ping 10.0.0.1 ...

Portus92 · 03-14-2020

Hi, here is a little network diagram :I tried to deactivate the firewall on the PC, but no effect.With ACL (applied on VLAN 10), ping to 10.0.10.11 doesn't match : Extended IP access list 110 10 permit icmp any host 10.0.10.11 20 permit icmp...

Portus92 · 10-26-2019

Thanks, I will buy a 2960 :)

Member Since	‎06-08-2019 02:50 PM
Date Last Visited	‎05-25-2022 12:02 AM
Posts	13
Total Helpful Votes Received	30

User Statistics

User Activity

Automatic ready state after phone failure

Hunt Pilot forward all

Site to site VPN not working

Remote access VPN no LAN access

Routing with VLAN

Re: Site to site VPN not working

Re: Remote access VPN no LAN access

Re: Routing with VLAN

Re: Routing with VLAN

Re: SG350 CLI