Sorry i forget to post this in complete version : C877_PF# sh arp Protocol Address Age (min) Hardware Addr Type Interface Internet 192.168.2.99 43 1093.e95f.5ca5 ARPA Vlan1 Internet 188.8.131.52 - 0000.0ce3.bde0 ARPA BVI1 Internet 192.168.200.250 0 649e.f3c0.16b6 ARPA Vlan2 Internet 192.168.200.254 - 001b.2bcc.fef0 ARPA Vlan2 Internet 10.100.11.2 65 0200.1a04.640e ARPA BVI1 Internet 192.168.2.3 0 7c61.93a1.c8ca ARPA Vlan1 Internet 192.168.2.7 54 001e.2a4a.4d90 ARPA Vlan1 Internet 192.168.2.4 0 20cf.302e.05e6 ARPA Vlan1 Internet 192.168.2.235 0 0008.9b8d.5e30 ARPA Vlan1 Internet 184.108.40.206 80 0200.1a04.640e ARPA BVI1 Internet 192.168.2.254 - 001b.2bcc.fef0 ARPA Vlan1 Internet 192.168.2.220 32 00e0.4cba.0e52 ARPA Vlan1 Internet 192.168.2.210 4 001e.e545.8d52 ARPA Vlan1 Internet 192.168.2.215 0 0040.8caf.d534 ARPA Vlan1 best regards...
... View more
Hi Everyone, I desperately need some help on a configuration I’ve been trying to complete unsuccessfully. Here’s the equipment I’m using: - Cisco C877 IOS : C870 Software (C870-ADVIPSERVICESK9-M), Version 12.4(6)T7, RELEASE SOFTWARE (fc5) - SPA112 for the ToIP FAI : - MANA (French Polynesia) ISP global architecture (Internet/ToIP): - one VC 8/35, pppoe for Internet, configured and operational - one VC 8/36, aal5snap for voice This is where I’m at: - Operator BOX : TG797V2, download of configuration file : OK - Using the configuration file, I can get the info regarding the VC and also the SIP account connecting info - Creation of 2 sub interfaces on the router : atm 0.1 et atm 0.2 - Under interface atm 0.1 = Internet, configured with Dialer, OK - Under interface atm 0.2 = ToIP, configured with IP address in DHCP - Both sub interfaces retrieve their respective IP addresses - I deactivated almost all ACLs so they don’t interfere with the tests - The SPA112 box cannot register In other words, my problem is that I can’t find a way to interface all the equipment above so my SPA112 box can register with the MANA Internet provider. Do I need to bridge all sub interfaces? If yes, which ones? Do I need to create a dedicated VLan to audio flows? Do I need to use NAT/PAT on the ATM 0.2 sub interface? I lack the competence to complete such configurations, so I would be very thankful to anyone who could help me out a bit on this one Here’s an excerpt of the "sh run" regarding the ATM sub interfaces : interface ATM0 no ip address no atm ilmi-keepalive dsl operating-mode auto ! interface ATM0.1 point-to-point description SOUS INTERFACE ADSL PVC 8/35 no snmp trap link-status pvc 8/35 pppoe-client dial-pool-number 1 ! ! interface ATM0.2 point-to-point description SOUS INTERFACE VOICE PVC 8/36 mtu 1500 ip address dhcp ip virtual-reassembly no snmp trap link-status atm route-bridged ip pvc 8/36 oam-pvc 0 encapsulation aal5snap Here’s an excerp of "sh ip route" Gateway of last resort is 0.0.0.0 to network 0.0.0.0 S 172.30.0.0/16 [254/0] via 220.127.116.11 C 18.104.22.168/16 is directly connected, ATM0.2 10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks S 10.0.0.0/8 is directly connected, ATM0.2 C 10.10.20.0/24 is directly connected, Tunnel0 22.214.171.124/32 is subnetted, 2 subnets C *.*.*.* is directly connected, Dialer1 C *.*.*.* is directly connected, Dialer1 S 192.168.1.0/24 is directly connected, Tunnel0 C 192.168.2.0/24 is directly connected, Vlan1 S* 0.0.0.0/0 is directly connected, Dialer1 Here’s an excerp of ip route conf ip route 0.0.0.0 0.0.0.0 Dialer1 10 ip route 10.0.0.0 255.0.0.0 ATM0.2 (I established a route to force the flow, and I doubt it serves a purpose) ip route 192.168.1.0 255.255.255.0 Tunnel0 NB : All suggestions are very welcome :), I’m running out of opions here and I would love to use my Cisco with that ToIP! I’m sure y’all can understand my frustrations.”
... View more