Hello, I am working with a Cisco SPA232D that has been factory reset and put into Bridge mode.I am trying to register it to a Digium (Switchvox) phone system. I have set the registration password for the extension set on the Digium and am putting in ...
Forum Posts
I had one of my SPA122 ATAs working perfectly with my FreePBX installation using SIP TLS and SRTP. I had it turned off for a month or two and just tried connecting it again and it doesn't work (SSL verify error or equivalent). I think that I read som...
Have had a UC520 in the field at my office for 10+ years, running 12.4(11r)XW3. ATT has been providing their SIP connection via fiber and a Cisco router to UC, with the UC hitting a remote SIP server, and things have been working great. They wish t...
Hi all hopeing you can help i have a ICS7700 system that was given to us as a startup to our business (trying to keep cost down) when powering on it only loads server 2000 but we wanted to start from fresh as we have all the cds that come with the or...
On a home network, a working SPA-2102 (software version 5.2.13[004]) is reducing internet download speeds to 7-12 mbps connected to a cable modem running at 100+ mbps. No specs seem to be available as to throughput capabilities of this device nor al...
Hi everyone. I am not an IT person. I don't know too much about computers but I've been given the task to get this conference phone set up. It just arrived and I plugged it in. I enter the apps menu to just get familiar with the device, but for some ...
i have Cisco Spa112 and i want to have MAC address in sip registrationthis is my contact string contact: "" <sip:1201@216.178.91.19:18823;alias=10.50.8.1~5060~1;x-nat=yes;pv-ip=172.16.1.3;pb-ip=216.178.91.19;pb-pt=18823;transport=udp>neither...
Hello ,SPA122 connected to the FAX machine , when I dial the VOIP no. I am getting the FAX tone but when dialing from the FAX machine any other FAX no. there is beep sound and then nothing ... Normal calls are working fine incoming and outgoing but t...
I can dial out but phone will not ring with incoming calls. lucky I have the phone diverted to my mobile phone but it should ring on cisco first then on to my mobile, if I miss the incoming call I do not know who called me. Phone status four orange a...
I have a cisco device SPA525G2 and I am not able to get the hold music it play. My SIP provider is saying that when I press the hold button on my IP phone, it is not sending a "reinvite packet" which is used to trigger their onhold music.On my softph...
IP Phone SPA 303:When I make a phone call and another call comes in, the phone does not report a busy signal to the second caller. What settings do I have to make so that the second caller hears a busy signal?
Hi,I use three phone numbers with my router: the first one is my private number, the second number is for fax and the third one is my business number. On the SPA 303, I receive both private and business calls. When I receive an incoming call, I would...
Good morning I have a Cisco SPA112, latest firmware 1.4.1 (SR5), configured to send logs to Papertrail but it seems to only be trying to send the logs to itself?! Why isn't it using the IP address I configured? This is the message I see regularly whe...
Hi all, I'm trying to use the ACME Certificate Service, with Let's encrypt. When trying to sign the CSR, I'm getting the following error:"There was a problem with a DNS query during identifier validation, Domain A-Record lookup failed" What am I miss...
Hi, I purchased a used Cisco UC520 from a business who no longer wanted it. However, they didn't know what the password to it was, so I cannot access the configuration. I would like to know how I can either reset the password, leaving the current fir...
