Hello Everyone, Thanks in advance for the help. I'm fairly new to Unified Communications, so please bear with me. I've been searching these forms about this issue and have tried a few suggestions but I still have the issue. When dialing from an exter...
Forum Posts
Hello, I've plugged a VIC2-2E/M card into my 2901 router but it isn't running (yellow/orange LEDs) My IOS version is C2900-universalk9-mz.SPA.154-3.M3.bin Any information would be greatly appreciated, thank you!
I have an estate office in Mumbai. I need an internet connectivity with a 1.5 MBPS ADSL connection. A VPN will be used to connect my office to the head office. Can u suggest the best Cisco routers and other related equipments??
Hallo, ich betreibe ein Cisco 303 IP Phone an einen neuen Router AVM FritzBox 7590. Der Router hat die neuste Software. Das IP-Telefon die Software Version 7.6.2f. Grundsätzlich funktioniert das Telefon. Es kommt jedoch regelmäßig zu dem Problem, das...
In my lab deployment, i'm using +e.164 pattern in the ITSP and DNs in CUCM. In the VG, i have the following outbound Dial-peer configured: dial-peer 110 (to CUCM)destination-pattern +1408555[0-4]... dial-peer 210 (to ITSP)destination-pattern +T if d...
I routinely have to lifecycle 50+ from a site. One of the longest parts of this process is documenting and transferring specifics onto the new phone profile IE. Extension, Identifying name, ECT.Is there anyway to transfer a phone profile to a differe...
Dears alll kindly need your support , i have AS5400 with IOS loaded version c5400-js-mz.123-16, i formatted the flash and loaded new version c5400-ik9s-mz.151-2.T1, i think this is wrong IOS because the router give message , " this version not suppor...
Hi team, it's been almost 4 months since I've had a SIP service paraded by mismatch codec issues. It's a TRUNK SIP from embratel operator, they use a Hauwei SBC on their side. I have an ISR29XX voice gateway with 128 PVDM. The carrier asked to change...
I have a new 8851 PCC Multi Platform phone. I plug it in and it comes up with an IP address. I can ping that address, but I can not bring up the phone's web page to configure the phone. There does not appear to be anyway to configure the phone from...
Dear Community. I have the followng issue:3CX system is the PABX voip we are using since 2 year. We have setup a VLAN for voip communication between IP Phone (Fanvill) and PABX. Al was working fine but recently after a firmware upgrade using that VLA...
Good day,I know you can register a cube to a sip provider. I've done that before.I also know you can register a ip phone (both sip and sccp) to a cube. I've also done that before.The question is if you can register a cube to another cube?And if so ho...
Hello guys, I have an issue. My cisco phone CP7821 does not ring when someone tried to call from outside. Internal calls it rings and phone is working fine. I am using a the GSM Interface from PSITEK which is connected to a router. I have checked t...
Is there anybody who can build ruggedized VoIP phones for harsh environment?
Apologies in advance for the low brow question. We currently have a 2 member stack of Catalyst 9300s as our core in our multiple locations. We have 2 SIPs, for redundancy. Unfortunately there is only 1 PRI line coming of the Telco Cisco router. Shoul...
Hi everybody,Please, i have an issue with h323 between my gateway Cisco As5400 and an Avaya CM PBX.From Cisco to Avaya, the calls work perfectly in H323But from Avaya to the Cisco Gateway using H323 i have a problem, the call does not connect.The ou...
