06-12-2008 11:10 AM
Dear how i can change username and password for PGW2200?
can give the procedures?
thanks,
Solved! Go to Solution.
06-12-2008 02:00 PM
You can change user parameters using usermod command in solaris. You can remove or add usernames using the useradd or userdel commands in solaris.
You can change a users passwd using solaris command:
passwd
Do not remove mgcusr username from the box. It is ok to change its password. For example, to change the mgcusr password:
passwd mgcusr
Enter existing login password:
06-12-2008 02:00 PM
You can change user parameters using usermod command in solaris. You can remove or add usernames using the useradd or userdel commands in solaris.
You can change a users passwd using solaris command:
passwd
Do not remove mgcusr username from the box. It is ok to change its password. For example, to change the mgcusr password:
passwd mgcusr
Enter existing login password:
06-15-2008 02:07 AM
to be understood.... for example, if i have:
username:mgcusr
password:pgw321
can i change both username and password?
or just only password? .... i am interested with both to change.
username=mgcusr is built in system OS or i can delet it?
thank you
06-16-2008 09:55 AM
Don't change the login user for mgcusr. Only change the password.
06-17-2008 01:08 AM
ok i did.
can please advise me for my other issue for SS7 signaling to add new E1.
06-21-2009 09:00 PM
Still we can add another user with full or minimal MML privileges...at least 9.7(3) Installation and configuration guide discusses how to do so.
06-15-2008 03:39 AM
it is ok ....
thank you....
---------------
i have now this issue:
i need to add new E1 to be in the same trunk for previous E1 which is for Abdali. new E1 will not have signal it depeneds at old one timeslot.
i used this for new E1:
prov-add:nailedtrnk:name="1033",srcsvc="ss7p-jtc-abdali",dstsvc="naspath1-abdali",srcspan="ffff",dstspan="0",srctimeslot="33",dsttimeslot="33",spansize=31
for old one this:
prov-add:nailedtrnk:name="1002",srcsvc="ss7p-jtc-abdali",dstsvc="naspath1-abdali",srcspan="ffff",dstspan="0",srctimeslot="2",dsttimeslot="2",spansize=30
============================
at AS5400 i used to add new E1:
controller E1 7/2
framing NO-CRC4
pri-group timeslots 1-31 nfas_d primary nfas_int 1 nfas_group 0
Is this true or there are other commands i should use?
----------------------------
OLD E1 is configured as:
controller E1 7/0
framing NO-CRC4
channel-group 0 timeslots 1
pri-group timeslots 2-31 nfas_d primary nfas_int 0 nfas_group 0
description Connection to Abdali
interface Serial7/0:0
no ip address
encapsulation ss7
channel-id 0
!
interface Serial7/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-ni2c
isdn incoming-voice modem
isdn map address . plan isdn type network
isdn rlm-group 0
no isdn send-status-enquiry
isdn negotiate-bchan resend-setup
isdn bchan-number-order ascending
no cdp enable
any help please for correct commands i shall use? please see attached file for details.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide