09-26-2013 03:36 PM
Hi guys,
I really don't understand what's going on. Maybe I'm wrong, maybe not. But.
I got a call on my voice-port 0/2/0. But my cisco matches the wrong dial-peer. This dial-peer matches by trunk group "common" which has port 0/0/1-0/0/3 (0/2/0 is not a member of the trunk group). Is it bug or feature?
cnx-rr01#sh voice call st
CallID CID ccVdb Port Slot/DSP:Ch Called # Codec MLPP Dial-peers
0xAD 152D 0x4AD5FF38 0/2/0 0/1:1 4255550103 g711ulaw 102/501
1 active call found
cnx-rr01#sh voice port s | i fxo
0/0/0 -- fxo-ls up dorm idle on-hook y
0/0/1 -- fxo-ls up dorm idle on-hook y
0/0/2 -- fxo-ls up dorm idle on-hook y
0/0/3 -- fxo-ls down down idle on-hook y
0/2/0 -- fxo-ls up up idle off-hook y
0/2/1 -- fxo-ls up dorm idle on-hook y
0/2/2 -- fxo-ls up dorm idle on-hook y
0/2/3 -- fxo-ls down down idle on-hook y
cnx-rr01#sh run | sec dial-peer voice 102
dial-peer voice 102 pots
trunkgroup common
tone ringback alert-no-PI
description ToPSTN
translation-profile incoming IN
translation-profile outgoing OUT00
preference 10
destination-pattern 9T
forward-digits all
cnx-rr01#sh trunk group common
Trunk group: common
Description:
trunk group label: common
Translation profile (Incoming):
Translation profile (Outgoing):
LPCOR (Incoming):
LPCOR (Outgoing):
Preemption is disabled (by default)
Hunt Scheme is round-robin
Max Calls (Incoming): NOT-SET (Any) 4 (Voice) NOT-SET (Data)
Max Calls (Outgoing): NOT-SET (Any) 4 (Voice) NOT-SET (Data)
Max Calls (MixTotal): NOT-SET (Any) 4 (Voice) NOT-SET (Data)
Retries: 0
Trunk 0/0/1 Preference DEFAULT
Member Timeslots : 1
Total channels available : 1
Data = 0, Voice = 0, Modem = 0, Pending = 0, Free = 1
Trunk 0/0/2 Preference DEFAULT
Member Timeslots : 1
Total channels available : 1
Data = 0, Voice = 0, Modem = 0, Pending = 0, Free = 1
Trunk 0/0/3 Preference DEFAULT
Member Timeslots : 1
Total channels available : 0
Data = 0, Voice = 0, Modem = 0, Pending = 0, Free = 0
Total calls for trunk group: Data = 0, Voice = 0, Modem = 0
Pend = 0, Free = 2
advertise_flag 0x00000040, capacity timer 25 sec tripl_config_mask 0x00000000
AC_curr 2, FD_curr 0, SD_curr 0
succ_curr 19 tot_curr 19
succ_report 19 tot_report 19
changed 1 replacement position 0
Current trunk : 0/0/1
09-26-2013 11:20 PM
Can you post the voice-port configuration?
Sent from Cisco Technical Support iPhone App
09-27-2013 12:18 PM
Hi Russel,
Sure:
cnx-rr01#sh run | sec voice-port 0/2/0
voice-port 0/2/0
supervisory custom-cptone CN-BELLCORE
cptone CN
timeouts call-disconnect 1
timeouts wait-release 1
connection plar opx 914255550103
description +86 400 XXXXXXX - Support IVR
station-id name China Support
station-id number +86XXXXXXXXXX
caller-id enable
10-02-2013 11:52 PM
Guys, do you have any thoughts by the chance?
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: