A few weeks ago, we installed a UC540 system for a customer with the SPA 509 ip phones. The customer has 3 Analog lines connecting to the FXO ports to connect to the PSTN. Caller-ID is enabled on the ports. When a call comes in from the PSTN, ...
A few weeks ago, we installed a UC540 system for a customer with the SPA 509 ip phones. The customer has 3 Analog lines connecting to the FXO ports to connect to the PSTN. Caller-ID is enabled on the ports. When a call comes in from the PSTN, ...
Hi, I have recently switched our phone system to VOIP and was supplied an SPA122 ATA to connect the old (really old) analog external ringer/bells. Needless to say after connecting the bells, they won't work. I'm assuming there is a compatibility iss...
Hi,When I connect to a mobile or cell phone from my Cisco ATA191 there is a 2 second delay between what one party says to the other party receiving a reply - which ATA191 settings should I check and/or modify to correct this? Landline to landline cal...
issuesspeaker headphone and mute all are blinking so is the message light 3 middle phone lights are a light orange constant nothing on the screen same result with identical phone and that's with just the power line in connecting to internet no differ...
Using an ATA 191 for analog-SIP conversion, we have a fax on line 1 and an analog phone on line 2. We experience following problem on line 2 with the analog phone: once the user finishes dialing (a 2 to 10-digits number), it takes 4 to 5 seconds for ...
Working with a university that has 110 - SPA112 ATA devices deployed across their network, that has been operating without an issue, had all SPA devices connect to the VoIP providers Device management service and pull a bad configuration file and loa...
Hi, I need to bring an issue to the community. I was trying to access the below link http://learningcredit.cloudapps.cisco.com/GET/lrncrd/jsp/index.jsp however it seems to be broken or unreachable with title Learning Credits Management Tool (LCMT)and...
Hello , i have upgraded the migrated the firmware of Cisco 8845 IP phone from enterprise firmware to MPP firmware. Firmware migration went well and all seems good.. but when i tried to register the IP phone over SIP TLS to Asterisk PBX , it is alwa...
Hello, i have a IP Phone 7970 which won’t even attempt to pull the Firmware from the TFTP Server after a Hard Reset (3491672850*#).I am using TFTPD32 by Phillipe Jounin as DHCP and TFTP Server.Under the „Log“ tab I can see that it sends a DHCP Reques...
Hello Community! I have a simple question, which I cannot solve. Maybe you have a simple solution.Is it possible to deactivate an unallocated DN automatically? Or vice versa.Like, i'm going to prepare a new CUCM(11.5). The Clients should get the same...
Hi all,Does anyone know a way to setup a custom button to forward the current call you are on to a predetermined phone number? For example, a caller calls an extension, the Jabber user picks up the call and presses a button that transfers the call to...
HI,We have recently purchased BE6K- UCSC-C220 server from cisco partner. Now i want to verify support documents with Cisco. please explain how to check service & support years in the cisco web site.
may any member help me in putting in service the device? It is connected properly to my Iphone 8 but I can't speak and receice any callthanks a lotregards Tanino
I'm a hobbyist. I use my Cisco 525G2 with a small private Asterisk server.I'm trying to configure a Plantronics CS-540 with APC-45 cable to work with my phone.I have enabled Electronic HookSwitch in the settings on the phone.I can't get the headset t...
Hi there. I've got a couple 525G2s - and trying to pair different headsets via bluetooth. After trying to pair, and not having my headsets detected, the handset then fails to work - no audio at all. Even after a factory reset.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: