Hi There,It seems that I'm doing something wrong, but i dont know what is it!.Im using CCA and UC520w, when i go to User/phones and then add, than phone type, i see around 20 types of phones, even though it should be way more, because when i go to ma...
Hello. I have a Cisco 540U with 2 Cisco 9951. I have followed the instructions for the wallpapers, and I confirm this because the 7965 we have can access wallpapers. The 9951 gives an error saying it cannot access additional wallpapers from the serve...
Hello, I have a problem with CME locale for 6941 SCCP phones. I have UC520 with CME 8.6.2 but I can not get on the 6941 other than EN locale. On phones 7945 it works without a problem. I found in the CME Localization Matrix that the location for 694...
I have a request to set a specific extension to only allow outbound/external dialing during a certain time frame. For instance, Ext 1234 can only call externally bettween 10am-4pm Mon-Fri. All other extensions would not have this restriction. We are ...
After upgrading the firmware of my SPA112 to 1.3.2(014), I cannot view the kernel or system log any more. The Log Module window shows the kernel and system services both have log enabled with a priority of Notice. Both have Local checked. In Log Set...
In spa-3102 is very easy: http://ubuntu4us.corp.eng.br/artigos/voip/asterisk-pbx-and-linksys-spa-3102 How to detect disconnect tone in spa112 ????
Hello friends,im having troubles with the uc540 im new in the world of cisco and im doing tests with this switch and some ip phones, im trying to configure the ip phones using the CCA 3.2 but i can´t always when i select some options related to the i...
Hi,I'm looking for a UK SIP trunk service provider. I dont wish to be tied to a specific ISP. Does a list of confirmed working providers exist?Best regards,Paul.
I need to figure out if my UC560 needs a software pack upgrade. The show version on the device console shows following. What software pack does it map to?Cisco IOS Software, UC500 Software (UC500-ADVIPSERVICESK9-M), Version 15.1(4)M5, RELEASE SOFTWAR...
Good Morning All,After bashing my head around this for some time, I finally narrowed down my problem. When our CISCO UC560 was installed, the installer configured an Auto-attendant per the company's request. During the day time hours, it's suppose ...
Hello!We use Cisco SPA504G with XML-Directory. If not found entry and pressing Dial, phone is freeze. Reboot only PoE cable disconnected. Firmware 7.5.5.
Hi everyone, I am trying to configure the CME to call 4 different phone numbers at the same time if I receive a call to a determinated phone number.Let's say I have a dn 317 dual line with a landline number 0011122337 associated. I want to forward th...
Hi all,I've a UC540 with telephony-service 8.0 and I set some hunt-Group like this:voice hunt-group 4 parallel final 510 list 214,215,216,217 timeout 600 pilot 508!!voice hunt-group 5 parallel final 995 list 201,202,203,204,214,215,216,217 timeout 60...
My voip provider supports two calls per line. When I'm on a call and a new call on the same line comes in, if I put the first caller on hold to answer the second call, then try to go back to the first call, I can hear them but they can't hear me. S...
I needed to add some licenses to a UC560 phone system. They came via EDelivery and I have the PAK. I went into maintenance/license management and entered the license info. It tells me Error: Failed to get License : - Send Request to Cisco Produ...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: