Hi I hope someone can help. We have installed a new uc320 for a customer in london, its running the newest firmware but the customer is reporting a lot of line noise. We have only heard this once but the customer is adamant that they can hear a hum o...
Hi there,I have a CME system with UC540 and a number of SPA509G phones. The reception phone has several extension numbers associated with it and I'd like to select one extension number to appear as Caller-ID.How to configure one specific extension nu...
Добрый день.Работает связка be3000 (8.4) + spa8800 FXO (6.1.7) для входящих городских вызовов. Клиент хочет АОН. Со стороны МГТС могут выставить Caller ID как FSK или DTMF. В обоих случаях при всех вариантах настроек SPA:Caller ID...
I have two UC540 running latest firmware setup as multisite. From one site to another site we need to use a scan to email feature, that uses SMTP port 25.But the UC at HQ is blocking it. I'm able to ping it, not sure what the issue is? any ideas?
Hi,I want to know about the followings support,Firstly, does UC 540 support CME 8.6? if yes then is it support SPA 500 series phones? if yes then can UC-540 register these phones over WAN using SSL vpn tunnels?Second, does cisco jabber in iPhone supp...
I'm looking to configure fax detect on the UC 520.I can get listen-first to work for faxes only. After 9 seconds, or when I press any key...the call is disconnected.If I confgure it for connect-first, the line just rings... never answers.Config is at...
Hi,I can't restore .cfg files on the Config Management menu. The "browse" buttonis not active and i can't load a file. The firmware version is 1.3.1. Tested with Firefox, Opera, Google ChromeInternet Explorer (old V6), same results. I haven't got pro...
Hello everyone, I have a UC560 with 3 Auto Attendants and BACD. We are having intermittent issues where calls are in queue and are not being delivered. Some users in the hunt group receive the calls, but others intermittently will not. They will see...
hello,can i configure all the fonctionalites of the UC520 with only CCA or should i also use the CUCM?
I have an AA set up to answer all incoming calls and transfer calls to 2 separate BACD group depending on what key is pressed. This seems to be causing CUE to hang and ring busy at times. Reloading CUE fixes the problem. STAC has told me that the ...
Hello,I have one UC540 with BRI Card and one UC560 with FXO Card.I would like to swap the BRI Card and FXO Card.Is supported by Cisco ?Is it possible ?and if yes I just need to power off the UC and swap the card ?Thank you,Sent from Cisco Technical S...
hello,i installed the cisco ip communicator on my pc and i tried to configure the network settings but it don't give me the possibilty to change the tftp server and the device name, i use the CCA for configuration. what can be the problem and is it n...
All-In a previous post, I asked, and was answered about 7.5.4 not 'sticking' for certain phones. https://supportforums.cisco.com/thread/2216529What I'm observing to be more specific is that the 7.5.4 is applied successfully (or so it appears on the d...
SPA112 doen't send the inbound CallerID to the phone. How can I enable inbound caller ID ?
I purchased a WRP400 wi-fi router (two SIP VoIP ATA ports) and loaded the latest firmware (2.00.32). This code is bugware. Not only do the configuration screens not work properly in FIrefox (it keeps giving "your connection has been reset by the peer...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: