I have a problem during setting up a new UC540 (it is updatet to the newest release 8.0.2)During the setup wizard, i cannot select any dialplan, because the configuration assistent notifies me, that he cannot find a appretiate "OutgoingDialPlan_WHATE...
Hi Folks,I have this weird issue where the SPA takes 9.7 seconds (as per looking in the tcpdump) after receiving the INVITE to return the 180 Ringing. But it returns the 100 Trying after 0.06 seconds so I know it got the INVITE.t0 => INVITE sent to S...
Is anyone running this phone combination successfully?Every customer we have ever installed this phone combo on has had the phone reboot on them randomly.We have had Cisco cases open for almost 2 years now with almost no results. (it appears the phon...
We have a small uc540 in house, and we have the wireless just hang occiassionally on us. If we wait long enough (could be 15 or 30 minutes, wireless networking will return (we never lose signal, just the ability to pass traffic). If we cable direct...
I have a 7961 with an expansion module where the screen died on a UC500 system.I have a replacement phone that I have attached the expansion module and plugged in but of course it needs the configuration assigned to the mac address of the old phone. ...
Hey yall,I have recently been tasked with upgrading our current 540 with a 560. We have a 35 person call center that is growing rapidly. My budget from Managment is CRAZY low and I was wondering what anyone thought of the following configuration belo...
Hi, we intend to change our UC solution from CME running on a 2901 to BE3K. As we are a small organization, we are using a BRI interface to connect to the public phone network. Our plan is to deploy BE3K and use the 2901 as a gateway to PSTN for BE3K...
Hello, I have a uc560 with around 30 phones deployed across the network inside a dedicated VLAN.Now I have a few phones that I cannot deploy into the Voice VLAN because they are connected to non-manageable switches, so I must deploy them at different...
how single teleworkes could connect to my offices cmbe 3000?i thought about VPN's and about jubber on mobile phone..what should i do to install jubber infrastructure on my company?does cisco have any phone which can establish ipsec vpn?
Good Morning,Other day I was given a SPA303 and told to make it work within our platform. I have taken on the task of downloading the SPCtool and generating the sample config into plaintext. I have turned this into a config file on my local machine a...
Hi Everyone,I have a customer that upgraded from an old Nortel Norstar system to a UC540 - the staff used to listen to the music on hold source through their phone speakers on the Nortel sets, and they are want to do this on the UC540 with SPA phones...
I am having problems configuring my SPA 303 to work with FreePBX. Right now I have 1 Grandstream 2000 fully functional on the network, but for some reason I can't get the 303 to work. I tried following some instructions on here, but the screenshots l...
BE6K questionsHi I am working on the BE6K and need to clarify few things about license:i have ordred : 218 cisco 692116 cisco 79456 cisco 7965LIC-CUCM-BA2ENH-AUC Manager Basic to Enhanced User License Upgrade - Under 1K13LIC-CUCM-BASIC-AUnified Com...
Hi, I have a Cisco SPA112, connected to a Draytek 2820 router, a fiber connection and using the SIPGATE VOIP service. Everything is working fine except my phone does not ring until the caller hears it ring 2-3 times; often causing me to miss calls. I...
Hi, I have uc320w with 2.3.2 (6) firmware and 2x SPA504g, 1x 508g, 1xspa303, 1 annalog phone @ fxs port. Both 504g are conected via wifi module. All phones are asign and work well in PBX system and ansfering all external calls even tranfers works wel...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: