Voice Systems and Accessories - Small Business - Page 399

Transfer to extension from personal voicemail greeting

I would like callers to be able to transfer to another extension if they reach someone's voicemail.For example:You've reached Bob Lawbla. I'm not in the office today. If you need immedate assistance please press 111 to be transferred to my assistant....

Resolved! Fax over SIP Trunk

I'm trying to setup a fax to work over a SIP Trunk I have with a Service Provider in Costa Rica... so far I think it is not possible to make it work with T.37 or Fax to Email because DSP limitations....Is it possible to create a single "relay to send...

Network requirements for IP Communicator

Hello,i am trying to get Cisco IP Communicator set up in my environment but currently i am unsuccessful. here is how my network is set up, is there any speacial configuration on the uc520 or switch that needs to be configured in order for this to wo...

UC520 FXS ports will not dial out

Not sure what is happening on this one. UC520 latest sw pack has decided that the onboard FXS ports will no longer dial out. Dialing inturnal extensions is fine both ways. DID's incoming to those FXS ports also work. Dialing access code 9 for the...

Resolved! UC320W - Voicemail attendant is silent

I just installed a UC320W. When I first set it up I didn't have any lines connected or anything. I wanted to make sure I understood how it worked before I deployed it. I was able to get in and setup my personal voicemail.However, now that I have the ...

Resolved! 7900 Series Sidecars -- They don't work?

We've had problems with 7900 series sidecars (and phones with sidecars on them) for some time. Recently this has been worse, and has given me the opportunity to research this across our customer base.What I found:7975 + (2)7916-24: We have 4 of these...

Help with UC560-T1E1-K9 - can not complete conference

Dear experts,I need help with my UC-560-T1E1. I'm trying to enable Meet-Me Conference. Using CCA --> Telephony --> Voice Features + Enable Multi-party Conferencing+ Mode G711 ( All phone use G711 as well)+ Maximum Multi-party session : 2 (1 for adhoc...

SPA8000 and PAP2T busy tone error

Hello,One of my customer have some Linksys SPA8000 and PAP2T products and when they try to use their analog FXS ports, they get busy tone instead of dial tone in fisrt 3-5 seconds. then it gives dial tone. If they reset products to check if problem ...

UC560 and Unified Call Connector

HiCan you confirm that i can have 100 users across 5 sites with a UC560 - this looks ok from the datasheets. There must be 2 attendant consoles for operator usage.Therefore I'm ordering the following:1 x SW-UCC-CME=1 x SW-UCC-SERVER 2 x L-SW-UCC-OPER...

Returning Netgear Switch - Help choosing Cisco Switch

Well, after hours of netgear support, we can't get the uc320 system working properly with VLAN's. I'm going to be returning the switch next week and diving into a cisco switch.We currently have a need for 20 ports. We may soon be moving to a new buil...

Broken Download for SPA 5XX Linux SPC tool

Hi Guys, The download for the latest SPA5XX Linux SPC tool is broken, the zip file returns unexpected end. Also the eariler version of the SPC tool will not run on linux, I get a segment fault when I exacute it. Appears to be the same problem men...

Cisco SPA509G to Cisco SPA509G

Is there a way to configure the phones (Cisco SPA509G) so that they talk to each other, like an intercom system?Or configure them to talk to each other, IP to IP?Basically internally we would have 16 Cisco phones, they would connect to a Cisco switch...

Resolved! ATA 186 connecting to a SPA3102

I have things hooked up as follows:PBX<==>SPA3102<==>ATA186<==>Analog phoneIP Addresses:SPA3102 - 10.1.1.144ATA186 - 10.1.1.45SPA3102 Config:Firmware 5.2.13(GW002)Line1 is off.Ethernet cable is connected to the Internet portOn the PSTN Line Tab: ...

SPA525G2 Won't Reboot

Plugged the phone into my network, made a factory reset (still had settings of previous owner on it) - then went to setup a Static IP address. Telephone rebooted and now its stuck at the Cisco screen. Tried unplugging/plugging several times, but it...

UC540 Dial Plans

I need some help with dial plans. We need a 10 digit dial plan as all local call must have the area code. The default that came with the US540 is North American 7 digit dial plan. Thanks

Voice Systems and Accessories - Small Business

Forum Posts

Transfer to extension from personal voicemail greeting

Resolved! Fax over SIP Trunk

Network requirements for IP Communicator

UC520 FXS ports will not dial out

Resolved! UC320W - Voicemail attendant is silent

Resolved! 7900 Series Sidecars -- They don't work?

Help with UC560-T1E1-K9 - can not complete conference

SPA8000 and PAP2T busy tone error

UC560 and Unified Call Connector

Returning Netgear Switch - Help choosing Cisco Switch

Broken Download for SPA 5XX Linux SPC tool

Cisco SPA509G to Cisco SPA509G

Resolved! ATA 186 connecting to a SPA3102

SPA525G2 Won't Reboot

UC540 Dial Plans

Meet and congratulate the February 2023 Spotlight Awardees!

Renew.cisco.com just got refreshed, and it will make your life easier!

Announcing Resources That Guide You to Success

7841 3PCC LDAP error connecting to server

SPA122 RC - Pending configuration

SPA303 Call History, External or Internal.

SPA112 Web interface hangs randomly, cannot configure network

SPA112 No line feed