Hey guys,I'm working on a design for a UC540W with SPA525G2 phones. I would love to find a way to program one of the line buttons to do the following when pressed:1. Dial an analog extension, insert 1-2 seconds of pause, then generate a DTMF tone.Fu...
I am unable to create a sub-menu within an AA script using the CUE web GUI.
Hello,we have 2 offices next to each other and connected to each other with a direct connection. So virtually the network falls on the same subnet. We are putting in one UC560 on each office(UC1 and UC2), each system has 4 FXO lines coming in. So we ...
I have a UC560 which is in a location (remote site) and I have a PBX in other location (headquarters) The extension of UC560 phones are 3xx y the PBX extensions are 2xx. I have a Gateway which is connected to UC560 via trunk SIP and this gateway is c...
Hello:I just installed SPA 122. For the first time everything was fine but there is no more ringing for incoming call. But the caller listens ringing tone, even it goes to voice message (but message is not recording too). Cahnge a lot of ring voltage...
Hi All,I have been testing some low end phones and I have to say I'm impressed with the SPA303. It works great with my platform (Siemens OpenScape Voice + Xpressions VM) with almost everything working straight out of the box. The only thing that I'm ...
Dear All,We are newbie on Cisco UC560.Our customer use Cisco UC560, ESW-520-24P and Cisco SPA 502G and 508G for their branch office replace old traditional PBX. Cisco UC560 have built-in VIC2-4FXO and VIC2-4FXS. Our customer PSTN line connected to UC...
Hi I have a BE3K with Australia country pack installed, but i would like to change the country pack for US branch, is there a way to do it without doing a fresh install ? Thanks.
Installed 3 SPA 504G with 3 different phone lines.Since customer has not got multiple SIP sessions with the provider (Engin) I put 3CX as an IP PBX.I mapped one of each of those numbers to one Ext on the 504's.So one number goes to Ext 1 which shows ...
So I am going to be trying to deploy a UC520 into an existing infrastructure with HP Procurve switches. From what I've read this is a little tricky. Just wondering if someone can give me a heads up on the problems I may encounter. If I plan to have t...
Hello,I recently purchased a SIP trunk from Voice Pulse. I have a Cisco UC500 that I configured the sip trunk on, this is registered with the Voice Pulse SIP server. The UC500 appears to be registered with the Voice Pulse SIP server. I can make outg...
Hi GuysDoes anyone know how I can forward a range of port numbers say 50000-51000 on UC540W ?Any help will be appreciated.Cheers
Good morning all, just installed 3 SPA 504G hooked in the office to a 3CX IP PBX.Since the customer has got 3 different phone numbers and the provider did not give them multiple SIP log ins, then the IP PBX (3CX) fixed it.The SPA 504G have been set u...
We are pleased to inform that 8.6.4 Australia & UK are now posted to CCO. URL : http://www.cisco.com/cisco/software/release.html?mdfid=283783671&reltype=all&relind=AVAILABLE&dwnld=true&softwareid=282074333&rellifecycle=&atcFlag=N&release=en_AU-CP-8.6...
I have a UC320 on 2.2.2 and am getting complaints that, when dialling out, the recipient has difficulty hearing the caller. This only happens with calls over SIP and not with calls over FXO. Is anyone aware of any way to raise the gain on the SIP tru...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: