Voice Systems and Accessories - Small Business

I have the cisco spa112 ATA and I'm trying to update the firmware; https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/csbpvga/spa100-200/release/source/spa112-122-rn-1-4-1-SR1/spa112-122-rn-1-4-1-SR1.html, but I cannot find any info on ATAs with a S...

I have several phones on multiple networks locking up (freezing). I have read several posts about the SMB phones locking up issue and it seems that there hasn't been much in the way of reproducing this problem.   I've been able to replicate the lock ...

Hello,Long story short, I'm looking to buy a Cisco SPA112 refurbished from a guy who sells ATAs, he showed me the ATA that he's going to sell to me and all, but the memory on it is 32MB. Quickly looking here https://www.cisco.com/c/en/us/td/docs/voic...

I have an issue with the SPA 122 fax capability.  SPA 122 device is register on UCM and making a call without any issues.  When i tried to send fax, connection was made with other end device but I'm getting failed massage while trying to send a docum...

Hi community , I have an ATA SPA122 connected to my modem router ..i'm not getting any audio. below what i have done so far :Network configuration :internet |MOdem Router (Hub 2000) - SagemCom fast 5250|SPA 122 (via internet : blue connection)|phone ...

I have bought a new Cisco Spa 8000 gateway and have update firmware to 6.1.12 and have 8 sip lines registered and working,the issue i have is incoming calls only ring in once and when first sip is busy it gives me busy tone,i want it to hunt to the o...

I'm having issue registering a 9971 phone on a UC520 running CME 8.6Here are the relevant configs -voice register global mode cme source-address 10.1.1.1 port 5060 max-dn 224 max-pool 56 load 9971 sip9971.9-2-2 load 7971 term71.default authenticate r...

Is it possible to have internal calls ringing all attached phones at the same time, just like it is possible for external calls via trunks and a ring all hunt group?

We have a UC540 in production.  It has been working perfectly for the last couple of years.  We added 3 phones last week that booted normally and we were able to make calls from.  Over the weekend all phones lost registration with the UC and none wil...

Plantronics Voyagre Pro UC V2 (BT300) was paired with my Cicso 525G2 until we did a factory reset on the 525G2 yesterday. The 525G2 is able to find the BT headset but will not accept the pin code 0000 hence unable to "connect" the 2.  Do we need to c...

I'd like to program my SideCar to only be a location for Speed Dial numbers. What's the programming language that I need to be putting into my interface to be able to dial outside of my small business location. I've discovered that putting nme:(inser...

Hello everyone,is it possible to register SPA112 with CUCM 8.6 nodes using SRV records at all?When I indicate IP address of the publisher, SPA112 gets successfully registered. However, when I configure SRV records on my DNS server for two callmanager...

I have 2 different phone models (SPA504G & SPA525G) in use, both on firmware 7.6.2a. My goal is to send text messages with Asterisk (MessageSend) to the phones.This works without any issues, but I also want to clear the messages on the phones (remote...

I have installed the SPA112 ATA Device, upgraded the FirmWare, and carried out the "Quick Setup", and created a SIP Line Extension and DDI in Avaya IP Office.   I now get a UK dialing tone, but when I try to dial out (to any number), from this Device...