I'm new to the UC560 world and am trying to get my NFR box setup on my network without removing my current firewall. I've gone through the attached guide and removed firewall and NAT configs. Right now I have the WAN port configured for an IP on my...
I recently purchased a SPA3102 from an online seller in Canada. If I have located the Firmware Version correctly, it is "Software Version:3.3.6(GW)". I'm not sure what the GW means.I have tried to upgrade by use of the "upg-spa3102-5-1-10-GW.exe" an...
Hi,With the annoucements today of the new equipment and position for the Borderless network, I was wondering if any of this translates down to SMB's (or will it in the future).Specifically, I'm interested in the Virtual Office, and will/can this be a...
I found VoIP A/C will failed registration with my VSP whenever my Firewall external IP changed. Reboot the SPA3102 cannot help, I have to remove the VSP domain from the "Proxy and Registration -> Proxy" field "Submit All Changes" and re-input the fi...
Hi,I was able to succesfully route from phone 1 to pstn 1 using a dialplan containing :gw0.If i want to route phone 1 to pstn 2 for example, what do i use? I tried the obvious gw1, but it doesn't work.Peter
In my country (the Netherlands) CLID doesn't work on SPA3102. A firmware update is promised on this forum, fixing those issues.Same applies to SPA8800. No CLID of KPN Telecom PSTN lines. I was hoping that the issues with SP3102 would result in a firm...
hey all.customer is on uc520, using spa525 phones. user manuals state you can view parked calls by hitting setup, status, call park status.. .then you can unpark calls in the list. we are not seeing this on the phones. is this setting on uc5xx ?th...
Hello,I would like to update my SPA922 to the latest firmware 6-1-5a.bin however the download link here: http://www.cisco.com/en/US/products/ps10036/ contains the firmware for the spa942 not the spa922. Can anyone attach the correct spa922-6-1-5a.bin...
In a voice system SPA9000, SPA400 & SPA9xx. SPA400 has 4 PSTN lines. Can we configure these 4 PSTN lines on 4 line buttons of SPA942 as a line selector. If line busy: shows red, if line free: shows green similar to the normal PBX system. Also can we ...
ok guys ... I'm pretty desperate right now ...what I did was I updated to the latest SW package UC520 8.0(1) using the latest version of CCA (2.2 I guess).I left the config alone (I have a pre-upgrade copy of my startup-config as well).after reloadin...
I cannot get this fax to email thing going. If someone could take a look at my config and point me in the right direction, I would appreciate it.The UC500 picks up the incoming fax call but the sending fax machine gets a communication error.I have a...
UC520 running uc500-advipservicesk9-mz.150-1.XAI have a line (423) set to CFA, when the number is called it sends out the local lines number as calling party.I have changed the calling-number to initiator and local.intitiator causes this to happen.Ca...
I've just set up a UC520 with 2 SPA508Gs and 2 SPA525gs.I'm using the Early adopter software for SPA508G compatability.My small problem is that the SPA508Gs pick up an IP address from the data Vlan, and show as unregistered. I've set them up manually...
Hi, I am trying to create a small VoIP test environment, using the SPA9000. I have a small, private, routed IP network (a couple remote sites over a Frame Relay network). Again, no ISP, all private addressing and private routers and switches. I would...
We have just upgraded our UC520 to version 8 and our bulk-speed-dials now do not work on our 7931G IP Phones, they work OK on our other IP phones.The phone loads have upgraded OkBut when we dial the prefix and the list number followed by the entry nu...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: