Voice Systems and Accessories - Small Business - Page 882

Changing the backgroung image in cisco 7970 ip phone

I'm using a UC500 and I'm trying to change the bckground image in a Cisco 7970 IP phone, I followed the steps in this link:http://www.cisco.com/en/US/products/sw/voicesw/ps4625/products_tech_note09186a008062495a.shtmlbut when I finished I still get a...

Swapping a 7940 phone

Hello,I have a customer that has a defective 7940 phone and I would like to replace the phone. Is there any procedure to do it so that we do not loose the voice mail settings (Unity Express) etc. The longer way is to add the phone as a new extensio...

Configure SIP with CLI

Hi!I'm trying to get the UC500 to work with our SIP providers. Since I'm in Sweden I can't use the fancy preconfigured SIP providers.I can't get it to work when doing it in the CCA 2.0. I wan't to se exactly how it's setup and if it registers with th...

Unified CallConnector- Dial Plan how-to?

I just installed Unified CallConnector in our Windows XP, make call with internal number was OK, but when try dial any other number such Local, Local Plus, National, National Plus..., which I have defined with UC520 I always get busy tone.It seem tha...

SPA8000 in UK - no dial tone, nothing - special cables?

Hi,I am not a VOIP expert, but I have set up a couple of VOIP system using SPA9000s and SPA941/SPA942 phones - all went well.However, I am now connecting some legacy stuff to a VOIP network and am trying to setup a SPA8000. I have configured my VOIP ...

Hardware conferencing using DSP question

I have a quick question regarding the number of max sessions for hardware conferencing and the codec(s) being used.I have a 48U UC500 that I want to maximize the number of max sessions for meet-me conferencing which is 4. In order to do this, I need...

SPA962: cannot connect PC through PC port

For years I have connected my laptop through my SPA962, but am now unable to do so.Both my PC and my SPA962 are DHCP enabled.I can connect both my PC and my SPA962 to the cable modem individually and they receive an IP address, netmask, gateway, and...

UC520 support both SIP and PRI via WIC?

Hello,I currently have a UC520 running 12.4.(22)T with a standard PRI installed to the WIC port. We are adding a new office and will be using a new MPLS/SIP connection to UC520. What I need to know is if the system will support both the PRI and SIP a...

Resolved! New coverged line for UC520

Gentleman and Ladies,This past year we bought a UC520 with 4 analog ports for our office. The unit is configured and running nicely. The contract on our T-1 is currently up and we are looking at possibly moving to either a PRI or SDSL or something ...

Resolved! Can I set a line or soft key to auto call forward?

Here is the scenario, I would image its fairly common, I leave my desk a lot to go out around the town on business. It would be nice if I could just press one button on my ip-phone to have my calls Call Forwarded to my mobile phone.So is there a way ...

Resolved! 7925G Push to Talk (PTT)

Is there any way to configure the 7925G's PTT on UC520 for directed, point-to-point voice call as opposed to group paging? Much like the functions you get with Nextel / Mike handsets?

WIP 310 Part numbers

This is a FYI.I had a query regarding buying a WIP310 .Seems there are three part numbers you can order;If you are offered WIP310-G1, WIP310-G2 or WIP310-G4, the G1/2/4 are related to the power adaptor;WIP310-G4 is AustraliaWIP310-G2 is EuropeWIP310-...

Resolved! International Fraud

We recently upgraded one of our clients UC520 to 20T2 and now they were recently notifed by their ISP (Cbeyond) that there has been some International calling from their end. Here is the dial-peer for all incoming callsdial-peer voice 1000 voipdes...

Removing centric line from UC520

I put in the request to remove my centric line form my pstn. How would I remove that configure from the UC520 and can this been done, so whenever the phone company removed the centric line, I will not loose the phones?