Voice Systems and Accessories - Small Business

Hello, I have two SPA2102 VoIP gateways. I would like to use them to extend PSTN line to another room using VoIP. Something like this:ISP router (with RJ-11 ports) <RJ-11> SPA2102 <RJ-45> LAN <RJ-45> SPA2102 <RJ-11> PSTN phoneHow should I configure t...

I have several PAP2N ATA’s and all of them work. They have a dial tone, can call other numbers and they ring a phone connected to them when they are called. The only issue I have is that if somebody is calling a number associated to an ATA, the conne...

Dear community,SPA504G has all 4 extensions set up. How to configure to appear busy to all incoming calls during a signle line activity? That is if line #2 is in an active session incoming calls to lines #1; 3; 4 should result in "busy". Thanx!

Hi, I´m trying to configure a Cisco cp-8851-3pcc, it´s supposed to be resset to factory settings, I´ve performed the resset holding # key and presing the secuence 123456789*0# and it seems to be with the factory default settings, but when I try to co...

I have been trying to find the TR-069 menu in my SPA504G web interface with latest firmware (7.6.2g) however there is no such tab. Does this model even support TR-069 at all?  

Hello , we are trying to detect if a Cisco TAPI device ( can be IP Phone , IP Communicator etc)  is disconnected from the network or powered off .  From TAPI we couldnt find an option to get an event in the case of such an incident.  We are not getti...

I have an 8841 Multiplatform connected to a Grandstream IP-PBX and I want to enable the auto-answer feature for intercom calls only. Is there a way to configure the 8841 to only auto-answer calls with the alert-type "Intercom". I have several phones ...

Not sure what is going on, all worked fine at another location. Can receive calls but when try to make outbound call I get a dial tone, then as soon as I dial the 11th number I get a fast busy signal. The outbound call does not even show up on the SI...

How do I fix this? Cisco is no longer able to help because they said my service coverage has expired. My voip company said that the phone is getting this message because it's having a hard time receiving an update and they can't help me either. Pleas...

I have the Cisco sg200-26 smart switch.  I have this connected : Modem (port 2 on modem)  to  Cisco Switch  from switch to computer, switch also has multiple other ethernet devices connected.  I also have a Linsys Velop router also connected to modem...

How can I listen to the music-on-hold through the phone?  On the old Nortel systems you would dial a feature number, so I'm looking to do something similar here like dial an extension or something.  Thanks.

we have 3 analog Voice gateways ( Branch ) that were working fine and registered to CUCM - 11.0  ( HQ ) via MGCP. - suddenly , two of them- FXS Ports shown " rejected" / "unregistered" -3rd one , is fine - - The two which have problems in separate ca...

Hello, My SPA504G is stuck in SOS Phone in Recovery Mode.  I have tried the recovery file for the spa962 document and received a notice of it not being reachable.  Is there a software update specifically for the SPA504G? Thank you!

I have installed on my server the Cisco Unified CM  with System version  10.5.2 .Some External Phone Number Masks are not working ( 2 week ago were working fine ) also every new phone number that i get from my telephony provider is not working. I hav...

Customer is migrating from SCCP to SIP phones on CME.   Existing phones have overlay buttons configured.  There does not seem to be feature parity for this on the SIP phones.What's the best way to handle what was a button with 3 dn's overlayed on it ...