So how does one utilise this licence installation and management screen? I was viewing the source and saw reference to this URL... http://192.168.1.xxx/license_install.asp;session_id= http://192.168.1.xxx/license.asp;session_id= Please share URLs y...
I am trying to configure an SPA 112 voip adapter to forward unanswered calls to my mobile phone. I have enabled this at the "Voice" menu under "Supplementary Service Subscription" and also at the "User" menu under "call forward settings". It simply d...
I've been having some trouble with my company's recently adopted PBX system and our 504G+S500 and found this post in another discussion (which was posted in the wrong area). I've reposted it below and am hopeful that this community might be able to ...
we have spa122 in our pbx. our pbx use star code with #. this star code don't work with spa122. it's possbile to use ? thanks
Hello group, Hopefully you can point me in a right direction. We use SPA504G phones with Asterisk. I do know how to setup phones and they work great. Now I want to automate provisioning and this is where I hit a brick wall. Not sure if it's firmwar...
I'm starting new thread on this because I believe I isolated issue as much as I can.. Simple requirement: to provision file via TFTP See attached archive. One file is spa504G.cfg - loads and applies just fine. I'm seeing syslog messages and other opt...
Question about creating spaxxxx.cfg files. I read somewhere that I should save .cfg file from template phone and then just modify it for new phones. I'm not sure I like it because it's really hard to navigate through those huge file.. Is it possibl...
I'd like to interface my UC520 to an overhead paging system (Speco multizone 70v Amplifier) According to the document below, FXO/FXS isn't an option, only E/M ports I tried a VIC-2E/M but it doesn't register even after a cold boot. Has anyone made a ...
Hi, I want to restrict the numbers that can be called by users on some analog phones plugged on uc540 fxs ports. I applied class of restriction (corlist) on ephone-dn but i'm not able to do that on voice-port 0/0/0. How may i manage that ? B...
Hi TeamAppreciate if you can let me know the SKU to order the Handset and Hanset Cord for the Phone SPA504G. Will be the CP-HANDSET-CORD= & CP-HANDSET= Compatible.? Those SKUs are the ones for the 7900 Series phones.Regards
Hello, I have Cisco SPA 525G2 with Software Version: 7.5.7s and Hardware Version: 2.0.0. I use https provisioning based on periodic resync. I found an issue with Programmable Softkeys -> Dialing Input Key List I want to use this settings: <Dia...
Hi I am trying to access the web interface on 4 cisco phones we have in the office. I have located the ip address but when I try and vist the ip in a browser I just get the error page 'Page can't be displayed' as if it is an invalid webpage. We hav...
I have a SPA3000 and I use it as a residential Switchboard (PBX). The problem I have is the Dial Plan seems to be limited to less than 1200 characters. My Dial Plan currently has 1,017 characters with 45 replacements and works well but I need to inc...
I have a door phone connected to my SPA112 and use the following dial plan: (S0<:752>) It dials as expected when I hit the button on the door phone, however, when the call is terminated another call is initiated immediately by the same extension. I...
Hello. I currently have 5 analog phones plugged into a spa8000, there is one main number and 5 truncs. The problem I"m having is that when one line is in use callers are receiving a busy signal instead of being transferred to one of the open lines. I...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: