Voice Systems and Accessories - Small Business - Page 445

Resolved! UC540 - Voicemail Access PSTN Number - Disabled?

Hi All,I'm wondering if anybody has seen this behaviour before, and can help me.I have a UC540, and am trying to assign a voicemail access number from the PSTN.Should be simple enough within CCA - but the 'Voicemail Access PSTN Number' field is greye...

Authentication Failed - Telnet (SSH Works Fine)

So I can SSH into my UC520 but I can't Telnet into it. When I telnet in, if I type the wrong password it says Authentication Failed then asks me to try again. If I type the right password it stills says Authentication Failed then immediately disconn...

SPA509G Firmware 7.4.9a Upgrade Broke Distinctive Ring

Hello all,I just upgraded two of the SPA509G phones on our system to formware version 7.4.9a. Now it seems that the phones are no longer honoring the Alert-Info SIP header and defaulting to the Classic-1 ring tone. This caused a minor revolt in the...

Resolved! Simplest way to forward all calls to a cell phone

Hi Guy´s.How was the simplest way to foward all incomming calls to a external cell phone? It should be easy managed by a button like FWD on a phone (SPA 525) in the system, independent of date and time.Thank you in advance,CHristian

SPA525G - (h/w version 2.1.0) Consult Transfer using SPA500S console not working - Fixed in 7.5.1a

Hello, When we try to do a consult transfer using the BLF keys on console, nothing is happening. This is apparent only on newer H/W version 2.1.0. The firmware used is 7.4.9c. I have got a SPA525 on 2.0.0 h/w version in my lab and its working fine o...

Resolved! UC560 - remote Site-to-Site VPN branch office teleworker?

I have a remote branch office voice vlan connecting to the remote UC560 via VPN tunnel to access the voice vlan 10.1.1.0/24 and CUE 10.1.10.0/30. My question is do I need to enable teleworker for these remote phones over this VPN tunnel?

Excessive moh multicast traffic

So I stumbled upon this while reading traffic on our Sonicwall router and noticed that we're dropping about 50 packets per seconds. Is there any way we can disable multicast moh 239.10.16.16 port 2000 on the telephony-service section without affectin...

Resolved! Prevent users from having to dial area code for out of market numbers...

Hi there,The situation:UC560 in corporate office with 525G2's connected via MPLS in another location outside of the local dialing area. The numbers were ported into the PRI's at the corporate office. These are in a different area codes. I want the...

SSL VPN download from CCA

When I go through the remote phone wizard, it tell me that I have to setup a full-tunnel SSL VPN and it sends me to the SSL-VPN setup page. I click on advanced and select full-tunnel and it tells me that I have to install the SSL-VPN and even gives ...

Resolved! External call in, CFwAll out - doesn't work

I have an auto-attendant where option 1 redirects to an external mobile number.When calling the auto-attendant internally, it works fine.When calling in from an external number, the call just gets dropped.The only differences in the debug are that wh...

UC560 AA Override

I am looking for a way that a user can input a code on the phone to override the AA schedule and put the AA into after hours mode. Is there a way to do this?

spa122 - ignore password parameters in provisioning file

Hi we are testing spa122 to implement it into our voip network.The problem we have found is about password parameters ignored in xml provisiong file, the same using the spc.The two parameters are:<Web_Login_Admin_Password>voip_test</Web_Login_Admin_P...

annexb = no on spa gateways

Hello, mine question is, why there are no support for 'Set_G729_annexb: No' for SPA series gateways. That is SPA gateway violates RFC 3555 (dating back to 2003) in its G729 codec naming. Snippet from RFC: MIME subtype name: G729 Required parame...

dial plan for toll free number 800

Hello,Anybody know's how to configure the dial plan for calling toll free number "800"thanks,Angelo

SPA502G Pantel VoIP Open Door

Hi,I have a issue with my SCCP Phones SPA502G, the call between the Pantel VoIP and IP Phones can be completed. But the function to open the door by pressing one digit, for example, 8 cant work it.Ive checked and maybe it was a bug of Pantel and the ...

Voice Systems and Accessories - Small Business

Forum Posts

Resolved! UC540 - Voicemail Access PSTN Number - Disabled?

Authentication Failed - Telnet (SSH Works Fine)

SPA509G Firmware 7.4.9a Upgrade Broke Distinctive Ring

Resolved! Simplest way to forward all calls to a cell phone

SPA525G - (h/w version 2.1.0) Consult Transfer using SPA500S console not working - Fixed in 7.5.1a

Resolved! UC560 - remote Site-to-Site VPN branch office teleworker?

Excessive moh multicast traffic

Resolved! Prevent users from having to dial area code for out of market numbers...

SSL VPN download from CCA

Resolved! External call in, CFwAll out - doesn't work

UC560 AA Override

spa122 - ignore password parameters in provisioning file

annexb = no on spa gateways

dial plan for toll free number 800

SPA502G Pantel VoIP Open Door

Congratulations to the Event Top Contributors Class of 2024!

Cisco + Splunk: It's a new day for your data.

A new chapter of the Spotlight Award begins!

Join us in Celebrating the New Year and the Nov.-Jan. Winners!

Announcing Resources That Guide You to Success

SPA525G2 fails https provisioning with custom CA

Cisco ATA191

peer to peer call in 7942G

cisco download process error (The download process was interrupted)

SPA 122 reboots at irregular intervals with reason code H0