Voice Systems and Accessories - Small Business

Hello I am new to the community, I would like the information because Ipurchase a uc560.I have already in my possession a vic2 2BRI-nt / nt, and I wanted to know if I can fit on a UC560-FXO-K9 and used both fxo the bri with the suppliedsoftware and l...

My SPA112 has decided it wants to stop providing dial tone and locks up on average of once per day.When it allows me to browse the Voice section on the web interface it simply says "Voice module not ready.".  When I try to reboot it from the web inte...

We have a client that had their UC500 configured usning CCA 2. version. My question is can you connect to it with CCA 3. version to make configuration changes?

I was looking into working with a client's headsets. Unfortunately I am not familiar with how wireless headsets with handset lifters work. I looked into it a little bit and I have found the lifter that coincides with their headsets:http://www.hellodi...

Hi, I am having a problem getting a new SPA509 phone to register to the system, but am having some issues.I have many other phones that are connected to the system. I believe that the problem is due to the switch coniguration, which is not an HP v191...

Hi there,I have tried the online device emulator and I have 2 questions.1. There is no Region Selection for Greece and it's not supported to any Region Pack. What region is more suitable in that case?2. I am planning to setup a sip trunk with an ITSP...

Hi -Have the need to assign a Intercom button on several 525G2's for which I would like to be prompted to enter what extension to Intercom once the button is pressed.  Today I have to tie up several buttons (Button 3 for IC to Ext 120, Button 4 to Ex...

Hi, I am having very poor voice quality on both FXO lines. I have tried using the impedance matching tool with no success. I actually have run the tool three times in a row with the same call test number and have gotten different results each time. E...

It happens with two different SPA2102 devices (5.2.10 firmware) that the service stop working (all the led of power data and phone, switch off and switch on). To restart the service we have to switch off the power, wait several minutes, and switch on...

Hi there,My SPA-2102 power light is blinking as follows:long RED3 x short GREENs. (when the power light blinks green the first time the ethernet light flashes twice in quick succession)I  cannot access the IVR and when it is connected to the interne...

I am using the above ATA with a local VSP but it keeps loosing the following settings even though they appear to be initially saved.Voice/Line 1/AdvancedOutbound Proxy:Use Outbound Proxy: yesRegister Expires: 3600Preferred Codec: G711uUse Pref Codec ...

I`m going to upgrade a UC520 from the 7.0 version to the 8.0.2, regarding to licesing what do i need to know before doing this? what problems could i find while doing this upgrade?TransGas_CME#sh platform software license Upgrade license             ...

ThinkPad hardwired to ESW520 from UC320 get speedtest results on 12Mbs Down & 8.5Mbs Up. Thinkpad on desk within 5 feet of UC320 with wireless connection to UC320 get 1/4 of the speedtest results. Any tweeks available to UC320 wireless configuration ...

HiI've got a PBX setup with SPA509's running on Asterisk 1.8.The customer has SPA509G's and wanted 11 of the button's to be BLF's, and a single button to act as a line button. So alpha tags could be used and easy changed if staff names changed I allo...

We are having an issue with UC520 licensing... to my knowledge the upgrade to the 8.2.0 software pack increases the licenses of all UC500's to 24 (actual 30)... this does not seem to be the case for 8u/16u UC520 boxes.Does anyone have any insight int...