Hi,Will there be a support(menu, features or firmware) for older SPA-phones, then 500 or 300-series to be connected to UC320W?Sent from Cisco Technical Support iPhone App
An automotive company has a Bridgespeak IVR from Shoretel. They are looking to integrate the iVR with UC560. I would really appreciate if I could get some documention and the requirements for the same.Thanks!!
I upgrade from 8.0.4 to 8.1.0 and everything was working until I reset one of the 7931 phones. The phone upgraded to the new firmware and the font on the phone went from normal to large and I have one 7965 and the font went from normal to small. I tr...
A site wants all MWIs turned off. A cisco tech gave me this command to run from CUE CLI:ccn application ciscomwiapplication aano enabledendAll of the MWIs are turned off on all phones except for one. Even if the user has no voicemails, the phone st...
We have a client interested in the SBCS, but all the computers in their office are Macs. I'm wanting to know if there are ways to run software such as IP Communicator and Unified CallConnector other than a virtual Windows machine through parallels.R...
Hi All,Hoping someone else has experienced this issue and I can learn from them.I am running a UC540 with 8.1.0 CME and 8.0.3 Voice Mail. If someone leaves a message in a voice mailbox, then presses the # key after the message it will prompt them to...
Hello expertsWe have UC540 and SPA504G phones. Incoming calls ring straight through on all lines on all phones. No hunting, no auto attendant.The last person to leave the office in the evening must enable call forwarding on all four TN's to an Answer...
UC320 does not act as internet router, so no WAN configuration. Is this possibly why voicemail to email that has been setup is not working. Can't seem to find any way to test and don't see anything in troubleshooting logs. Also - is there any way ...
New UC320W. After considerable effort I was able to upgarde the frimware to v2.0.6 (from 2.0.1). This save issue occurs in both the old and new firmware.During the initial setup wizzard:I am able to save the configuration to my local hard drive.Att...
Hi,I'm considering upgrading the voip/router setup in my small office. The UC320W seems to meet all my requirements, but I'd like to confirm whether the Cisco 857 ADSL/Router would be a good choice ahead of the UC320W? I guess its primary use is just...
So I wound up with two UC320 test system for review, and I thought I would put my impressions, questions, RFE's here to see what's what.Nice design, gets a little hot, and I hope it's not just a rebranded SPA9000I was surprised at no CCA support as I...
Considering that the UC320W is supposed to control the network it would be nice if you could assign reservations in DHCP.I believe you can do this in some of the consumer products, like the Linksys E3000.The user see's the list of DHCP leases and can...
Hi,Does anyone have any experience with interconnecting a UC520 with Avaya office telephony?We have attempted to get a SIP trunk working in either direction and I can get the SIP headers/diagnostics with 'term mon' and 'debug ccsip all'. however I ca...
We have a UC560 system set up in our business and I am looking for some advice on how to impliment something. We have two businesses at our location and both share the same phone system. A couple of the employess (Mainly management) work for both bus...
Hi everyone. I just added a new 7965G to my UC560 system, everything went fine in CCA. Upon registering though, the phone's time is off exactly 3 hours (behind). I'm sure this is a time zone issue, but, all my SPA phones are showing the CORRECT ti...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
