Cannot Access CUE

[zach.moody]

I can't seem to get into CUE. When I do a "service-mod I 0/0 sess" all that happens is this...

UC560#ser i 0/0 sess

Trying 10.1.10.2, 2002 ... Open

I can try resetting it, clearing the session and reopening, but it continues to do the same thing. I can't even get a bootloader prompt so I can restore the software on it. Anyone have any ideas on how to fix this?

[David Trad]

Hi Zach,

Couple of things to try first:

1. Run the service module command, but instead of session put "status" there and show us what the current status is of the module.
2. Power the system right down, then power it back up and give the CUE module approx 4-6 minutes to boot up before trying to session into it
3. If point two does not work, run the service module command again and use the "reload" command, but imediatly after doing so session into it imediatly, always make sure you press the enter key twice when ever you try to session into the CUE module as well.

Hope this helps.

Cheers,

David.

[zach.moody]

Hi David, thanks for the reply.

Currently the status shows the following:

UC560#ser i 0/0 status

Service Module is Cisco Integrated-Service-Engine0/0

Service Module supports session via TTY line 2

Service Module is failed

Service Module heartbeat-reset is enabled

Service Module status is not available

After I do the reload (I tried to session into it immediately afterwards to no avail) it shows this:

UC560#ser i 0/0 status

Service Module is Cisco Integrated-Service-Engine0/0

Service Module supports session via TTY line 2

Service Module is trying to recover from reset/shutdown

Service Module heartbeat-reset is enabled

Service Module status is not available

After that's displayed for about 20min it goes back to the "Service Module has failed". When I cycle power to the device it says something to the effect of waiting for registration messages (I can post the exact error tomorrow) then eventually reverts to the same Service Module has failed message. I noticed the 2gb CF card it came with was unformatted. Is that where the boot loader and system files are stored?

[Steven DiStefano]

Try hitting enter a few times. It's a console session which needs to

wake up.

Maybe something else is connected (it's one at a time).

On Jul 12, 2010, at 4:06 PM, "zach.moody"

[zach.moody]

Yeah, I've tried that. Nothing seems to register.

[cristobal.priego · Accepted solution]

Zach,

remove the default route to cue, add it back in and it's going to work

[zach.moody]

Perfect, I can get to the boot loader now. Thanks!

[zach.moody]

Well, spoke too soon. I had to reboot and now, even following that process, I can't get back into the CUE.

[Dan Smith]

i have the same issue with a UC560. everything was working, then suddenly i cannot access CUE. here is what i get

UC560#service-module integrated-Service-Engine 0/0 se
Trying 10.1.10.2, 2002 ...
% Destination unreachable; gateway or host down

UC560#service-module integrated-Service-Engine 0/0 status
Service Module is Cisco Integrated-Service-Engine0/0
Service Module supports session via TTY line 2
Service Module is failed
Service Module heartbeat-reset is enabled
Service Module status is not available

no matter what i do as far as rebooting or power cycle i get the same message. seems dead, but i thought maybe someone might have a trick or two. lucky it is not in productions so i will be calling tac on monday.

[jbrunstein]

I am setting up a UC560 and facing exactly the same issue.

UC560#service-module integrated-Service-Engine 0/0 status 
Service Module is Cisco Integrated-Service-Engine0/0
Service Module supports session via TTY line 2
Service Module is failed
Service Module heartbeat-reset is enabled
Service Module status is not available

UC560#

Did you get an answer from the TAC and what was the solution ?