Please be advised, the GuideMe Wizard is no longer available on the Small Business Support Community. For search capability please use the community search field to find content related to Cisco Small Business documents, videos, and discussions.
Welcome to this guide. Today you will learn how to properly set up a Cisco UC520 as a New and used device. The first section will be for a NEW UC520.
Step 1- Start your UC520 by plugging it in. Make sure you plug your Laptop or PC into one of the 8 ports on the front of the device.
Step 2- While it is booting up, download and open Cisco Configurations Assistant also known as CCA.
Step 3- When the fans in the unit calm down (slows down), Click Add new community.
Step 4- Put the ip address as "192.168.10.1"
Step 5- Once your Laptop or PC finds the UC520, it will prompt you asking for a username and password. It is:
Step 6- Once you get in, the telephony wizard should pop up, if it does not open it up in the first tab.
Step 7- Configure your router to fit Homelab/Business needs.
Step 1- Open up Tera Term (do not use Putty)
Step 2- Plug your consel cable to your UC520.
Step 3- Apply power to your device.
Step 4- Hold the "Pause and Break" key on your computer's keyboard.
Step 5- Wait until this shows up:
rommon 1> Confreq 0x2142
you must do a reset for this to apply
rommon 2> reset
Step 5- Let the device finish booting and then say NO to the prompts .
Step 6- Follow this:
Step 7- Now exit to Enable mode. Now say "Copy Flash:(Something like this "UC520-8U-4FXO-K9-factory-8.6.1.cfg")
Step 8- Once it stops doing all the reconfigurations, go to enable mode and type this in "service-module integrated-service-engine0/0 shutdown". This ensures that your CUE also know has the voicemail/telephony service module's CF card does not get corrupted after you remove the power.
Step 9- Once it says "004623: Aug 15 19:57:48.404: %SERVICEMODULE-5-SHUTDOWN2: Service module Integrated-Service-Engine0/0 shutdown complete" or something like that, remove the power. Wait 10 seconds then reapply the power to the device.
Step 10- While it is booting up, download and open the Cisco COnfigurations Assistant also known as CCA.
Step 11- WHen the fans in the unit calm down (slows down), Click Add new community.
Step 12- Put the ip address as "192.168.10.1".
Step 13- Once your Laptop or PC finds the UC520, it will prompt you asking for the username and password. It is:
You have ended this tutorial on how to set up a UC520. If you would like to see the video, please click on this link here: (NO LINK AT THIS TIME).
A consumer router may support a virtual private network (VPN) connection, but that's a far cry from the network and security capabilities that a business-class router can provide. All it takes is some IT talent and know-how to set one up. You're hear...
Cisco RV340 Series Secure Router
Security License Features and Performance
Today, secure networking is imperative for every business, even the smallest one. The RV340 series security routers provides business users with advanced connectivity and...
Recorded Live at SpiceWorld 2018!With the increasing complexity of technology lengthy configurations, dealing with multiple vendors, constant updates and maintenance –it can feel like you are navigating an unruly IT jungle. Join Cisco's Amy Blanchard as s...
Small Business Networking Products
Network and Smart Storage
FindIT Network Management
Voice and Conferencing
ATAs, Gateways,and Accessories
This document is attempt to recreate content of original document created by famous @Patrick Born. Cisco has considered to destroy such valuable document for an unknown reason.In order to capture debug and syslog messages from your SPA1x2 and SPA232D phon...