cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
2750
Views
4
Helpful
6
Replies
Highlighted
Beginner

SPA303 with CME 8.6 on 29xx routers using SIP

Hello,

one of customers wants to use SPA303 phones with CME 8.6 running on Cisco 29xx series router using SIP. I was trying to find any trustworthy documentation or compatibility matrix which would definitely confirm that it will work without any issues, but everything was only about integration using SPCP (which I know is not possible with 29xx routers).

Could someone pls confirm it's working or even better point me to the right documentation ?

Thanks

Marek

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
Beginner

Hola Amigos,

 

It works propertly for me. First you must configure your spa303 in sip-mode

https://supportforums.cisco.com/discussion/11047051/how-do-i-access-spa-303-admin-webpage

Then, you need to manually configure your sip server parameters (cme-ip-address)

Finally add this configuration in you cme:

voice register dn  x
 number zzz
 name IT
 label zzz
!
voice register pool  x
 id mac aaa.aaa.aaa
 number 1 dn 41
 dtmf-relay sip-kpml
 voice-class codec 3
 username zzz password cisco
 no vad

 

 

View solution in original post

6 REPLIES 6
Highlighted
Beginner

i'm facing the same problem, can anyone advise please?

Highlighted

Highlighted
Beginner

Hola Amigos,

 

It works propertly for me. First you must configure your spa303 in sip-mode

https://supportforums.cisco.com/discussion/11047051/how-do-i-access-spa-303-admin-webpage

Then, you need to manually configure your sip server parameters (cme-ip-address)

Finally add this configuration in you cme:

voice register dn  x
 number zzz
 name IT
 label zzz
!
voice register pool  x
 id mac aaa.aaa.aaa
 number 1 dn 41
 dtmf-relay sip-kpml
 voice-class codec 3
 username zzz password cisco
 no vad

 

 

View solution in original post

Highlighted

Hi, i am trying to configure a 2901 CME SRST,  IOS 15.0(1)M5. Do i need to upload cme 7.1 since i am using SPA 303 and 509g? Or i dont need it?

If i do need it, where can i get it? I dont have a cisco contract, te supplier says they also dont have a cisco contract.

Please help.

Highlighted

SPA3xx as well as SPA5xx are not supported by CME.

You can connect them as just unknown third party SIP device only.

Highlighted
Beginner

I know this is an old thread, but I hope this helps someone else because I ran into this and could have saved huge amounts of time if I had a bit more info.

 

As Guillermo says, this does work. I just got it running in a home lab. There's actually a Cisco provided document describing the solution. See attached. Pages 3-7 describe how to set up an SPA phone on CME. I got it working with an SPA303.

 

Edit: Here's a copy of my SIP related config:


voice service voip
 allow-connections h323 to h323
 allow-connections h323 to sip
 allow-connections sip to h323
 allow-connections sip to sip
 no supplementary-service h450.2
 no supplementary-service h450.3
 no supplementary-service h450.7
 sip
  bind control source-interface GigabitEthernet0/0
  bind media source-interface GigabitEthernet0/0
  registrar server expires max 1200 min 300
!
!
voice register global
 mode cme
 source-address 192.168.1.14 port 5060
 max-dn 100
 max-pool 25
 time-format 24
 date-format D/M/Y
 tftp-path flash:
 create profile sync 0019406339824212
!
voice register dn  1
 number 3
 shared-line
 label Foozand! //This is just a banner that displays at the top of the phone
!
voice register pool  1
 id mac 34DB.FD5E.B8C9
 number 1 dn 1
 dtmf-relay sip-notify
 username user password yourphonepassword
 codec g711ulaw

 

Hope this helps.

Grant