UC320 - MEDIATRIX - ISDN ITALY

[fabrix1971]

Good morning.

I have installed UC320W and Mediatrix 4402. I followed the guide for Mediatrix.

I am able to make call with analog line , but i am not able to make or receive call with BRI ISDN.

It possibile to use POINT TO POINT or i MUST user POINT TO MULTIPOINT?

Thanks

[fabrix1971]

In the deploymnet guide for mediatrix 4400 i have read the must to be set to POINT TO POINT,

but my ISDN provider is set to POINT TO POINT:

Can it works?

Thanks for a replay

[fscharz]

Hello Fabrizio,

I like to do a Webex with you tomorrow morning.

can you please call the support line under 800 928 322  and ask for me?

Do you know the software version of the Mediatrix?

Regards,

Friedrich

[fabrix1971]

Hello Friedrich, Di you speak italian?

I have called 800928322 this morning.

I have to send log from UC320W and Mediatrix to a tecnician that have answered to me.

If you want i can call you tomorrow morning, but i don't speak english very well.

However,

i have try to set to POINT TO MULTIPOINT.

I am able to receive call but when i try to make a call from ipphone i receive the messagge "INTERNAL SERVER ERROR",

or SERVICE NOT DISPONIBLE (Servizio non disponibile).

When i receive call from ISDN number it works, but sometimes no ipphone ring.

I think that is a problem in ISDN configuration of MEDIATRIX, such as MAXIMUM CHANNEL or

other configuration.

Have you understand?

[fabrix1971]

Hello Friedrich,

this is screenshot fo Mediatrix Firmware

System Description:	Mediatrix 4402
	Firmware:	Dgw 2.0.12.230
	Profile:	44XX-MX-D2000-78
	MAC Address:	0090f8071b69
	Serial Number:	002210001S321110310
	System Uptime (D:HH:MM:SS):	0:00:03:02
	System Time (DD/MM/YYYY HH:MM:SS):	31/12/1999 19:02:44

[fabrix1971]

this the route setting

Status

Config Modified: no Route Type Sources Properties Criteria Expression Criteria Mappings Signaling Properties Destination User sip-default None hunt-test User isdn-Bri1, isdn-Bri2 None sip-default Signaling Properties Name Early Connect Early Disconnect Destination Host Allow 180 with SDP Allow 183 without SDP Privacy SIP Headers Translations Call Properties Translations SIP Headers Translations Index Name SIP Header Built From Fix Value Call Properties Translations Index Name Call Property Built From Fix Value Hunt Name Destinations Selection Algorithm Timeout (seconds) Causes test isdn-Bri1, isdn-Bri2 Sequential 0 31, 34, 38, 41, 42, 43, 44, 47 Available Interface (ISDN/R2/POTS endpoints and SIP Gateways) Name sip-default isdn-Bri1 isdn-Bri2

and this the ISDN setting

	Endpoint Type:	TENT
	Clock Mode:	AutoMasterSlave
	Monitor Link State:	DisableEnable
	Connection Type:	Point To PointPoint To Multipoint
	Signaling Protocol:	DSS1QSIG
	Network Location:	UserPrivatePublicTransitInternational
	Preferred Encoding Scheme:	G.711 a-LawG.711 u-Law
	Fallback Encoding Scheme:	G.711 a-LawG.711 u-Law
	Channel Allocation Strategy:	AscendingDescendingRound-Robin AscendingRound-Robin Descending
	Maximum Active Calls:
	Signal Information Element:	DisableEnable
	Inband Tone Generation:	DisableEnable
	Inband DTMF Dialing:	DisableEnable
	Overlap Dialing:	DisableEnable
	Calling Name Max Length:
	Exclusive B-Channel Selection:	DisableEnable
	Sending Complete:	DisableEnable
	Send Restart On Startup:	DisableEnable
	Link Establishment:	On DemandPermanent
	Hook-Flash Keypad:
	Accepted Status Causes:
	Accepted Progress Causes:
	Send Isdn Progress:	Send AllSend InbandSend Alerting
	Send Progress Indicator IE:	Send AllSend Inband Only

[fscharz]

Hello Fabrizio,

please call the support line after 9 am your local time. Don;t worry about the level of English, I can allways get someone to translate.

Speak to you later,

Friedrich

[fabrix1971]

Hi have try ti set "link establishment"  from "on demand" to "permament".

it seems that I am able to make outbound call

I'll try to make and receive call.

I'll be call you tomorrow.

Bye