cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
Please be advised, the GuideMe Wizard is no longer available on the Small Business Support Community. For search capability please use the community search field to find content related to Cisco Small Business documents, videos, and discussions.
1062
Views
0
Helpful
10
Replies
Beginner

UC520 version 8.6.2 Voicemail will not work

We have a UC520 that we erased and reinstalled 8.6.2. After installing and configuring - via CCA Wizard - voicemail does not work. If you call the voicemail extension it just has dead air. If you call an extension and the user for the extension is busy, no answer or selects DND you get dead air. Rebooted system, reinserted compact flash. Configured as a PBX and did it again and configured as a Key System with same issues. Any suggestions?

Everyone's tags (4)
10 REPLIES 10
Enthusiast

UC520 version 8.6.2 Voicemail will not work

Hello,

What happens when you check the CUE status? Can you ping CUE at 10.1.10.1?

Thanks,

-john

Beginner

UC520 version 8.6.2 Voicemail will not work

According to the CCA voicemail diags, it responds voicmail is opperational. No I cannot ping 10.1.10.1. I can connect to 10.1.1.1, 10.1.1.1/ccme, 10.1.10.2. Yet cannot connect to 10.1.10.1.

Thanks appreciate the assistance.

Enthusiast

UC520 version 8.6.2 Voicemail will not work

Hello,

Ok, you need to add a route either on your PC or your default gateway to the CUE network. If you are unable to communicate with CUE and are using CCA, it is possible the necessary configurations are not present in CUE, since your PC is unable to communicate with CUE. Once you can access CUE web interface, check the call-in numbers configuration.

Thanks,

-john

Highlighted
Beginner

UC520 version 8.6.2 Voicemail will not work

The following is the route listed in running config via CLI

ip route 10.1.10.1 255.255.255.255 Integrated-Service-Engine0/0

Thanks

Enthusiast

UC520 version 8.6.2 Voicemail will not work

Hello,

But is the UC your default gateway?

Thanks,

-john

Beginner

UC520 version 8.6.2 Voicemail will not work

Yes, it is my default gateway. We configured via cca wizard. Pretty much answered questions. Used almost all defaults, except wan address of course.

Enthusiast

UC520 version 8.6.2 Voicemail will not work

Hello,

Can you post the configs for the following:

Service-module Integrated-Service-Engine 0/0

Loopback0

Can you session into the CUE in CLI and tell me what you get?

Service-module Integrated-Service-Engine 0/0 session clear

Service-module Integrated-Service-Engine 0/0 session

Enter you login credentials

Hit enter again

Thanks,

-john

Beginner

UC520 version 8.6.2 Voicemail will not work

Used your 2nd command service-...session. I was able to enter into se-10-1-10-1#. Didn't use the ... clear command. Did you want us to run that command?

I also attempted to upgrade/reinstall the voicmail package only via CCA Maintenance, restart/reset. Once it got to backup said it could not go forward because cue could not communicate to pc.

Beginner

UC520 version 8.6.2 Voicemail will not work

Correction on my last post. I attempted to upgrade via CCA Maintenance button but via the upgrade then uc500 folder under the Maintenance button.

Also here is what our loopback looked like.

ip tftp source-interface Loopback0

!

!

!

bridge irb

!

!

!

!

interface Loopback0

description $FW_INSIDE$

ip address 10.1.10.2 255.255.255.252

ip access-group 101 in

ip nat inside

ip virtual-reassembly in

Enthusiast

UC520 version 8.6.2 Voicemail will not work

Hello,

Ok, it sounds like you can get command line access to CUE, but something is preventing you from connecting to CUE by IP.

Can you post the configs for the following:

Service-module Integrated-Service-Engine 0/0

and

show ip route

Thanks,

-john