cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Get the latest new and information the November issue of the Cisco Small Business Monthly Newsletter

744
Views
0
Helpful
7
Replies
Beginner

UC560 with FXS ports that gets useless after some time of use

Hi everyone,

I've an UC560 with 4 FXS ports built-in.

In 2 of the 4 ports of the UC, I've configured 2 stcapp phones.

After  some time of use, these 2 ports became unavailable, so I've to make the  command "shut" and "no shut" to return to life these 2 ports. They  remain working during some amount of time and became unavailable again,  and the solution is the same, "shut" "no shut".

Anyone have experienced this?

Here's the configuration of the ports:

voice-port 0/0/2

compand-type a-law

cptone PT

timeouts interdigit 20

timeouts ringing infinity

station-id number 341

caller-id enable

!

voice-port 0/0/3

compand-type a-law

cptone PT

timeouts interdigit 20

timeouts ringing infinity

station-id number 350

caller-id enable

dial-peer voice 3 pots

corlist incoming internacional

service stcapp

clid network-number 341

port 0/0/2

!

dial-peer voice 4 pots

corlist incoming interna

service stcapp

clid network-number 350

port 0/0/3

ephone-dn  41  dual-line

number 341

corlist incoming internacional

!

!

ephone-dn  50  dual-line

number 350

corlist incoming interna

Best Regards,

LuisM

7 REPLIES 7
Hall of Fame Master

Re: UC560 with FXS ports that gets useless after some time of us

Are you running the latest software pack? If not, update and check again.

Beginner

UC560 with FXS ports that gets useless after some time of use

Hi Paolo,

Thanks for your answer.

I don't have the latest CME, is that what you refer?

Best Regards,

LuisM

UC560 with FXS ports that gets useless after some time of use

Hi Luis,

Yes means both IOS, CME and CUE which are included in current software pack 8.2.

Best regards,

Alex

Highlighted
Beginner

UC560 with FXS ports that gets useless after some time of use

Hi Alex,

I had already considered this option but I want to use it as a last resort, I'm looking now for other tips, but it's an option open.

Thanks for your help.

Best Regards,

LuisM

Hall of Fame Master

Re: UC560 with FXS ports that gets useless after some time of us

You should not consider having an updated system as an option, but as necessary step to get best results.

Rising star

UC560 with FXS ports that gets useless after some time of use

Hi LuisM,

I am confused a little here, so please confirm or set me straight.

Looking at your configuration it resembles that of an FXO configuration not an FXS, although I do know in some countries the Carriers do use FXS for hand-offs, are you in a country where the carrier does this, or did you mean to say FXO and not FXS??

Is this system CLI configured or is it CCA configured?

Cheers,

David.

Cheers, David Trad. **When you rate a persons post, you are indicating a thank you or that it helped, but at the same time you are also helping to maintain the community spirit - You don't have to rate posts and you wont be looked down upon :) *
Beginner

UC560 with FXS ports that gets useless after some time of use

Hi David,

Thanks for your answer.

It's an FXS, for sure, because it is already built-in in the UC.

This is CLI configs.

Show ver:

Cisco UC560-BRI-K9

4 Voice FXS interfaces

Best regards,

LuisM