cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
357
Views
0
Helpful
12
Replies

AnyConnect new feature - DTLSv1.2

With the release of v9.10.1, has anyone been able to get DTLSv1.2 working with AnyConnect sessions? (Our clients are v4.6.02074)


-If I don't specify dtlsv1.2, it will always establish the DTLS tunnel using dtlsv1.0.


-If I do specify dtlsv1.2 with the following config, the DTLS tunnel fails to establish with the message "%ASA-5-722043: Group <groupid> User <userid> IP <ipaddress> DTLS disabled: unable to negotiate cipher".   Removing the "ssl cipher dtlsv1" line makes no difference.

 

ssl server-version tlsv1.2 dtlsv1.2

ssl cipher default custom "ECDHE-RSA-AES256-GCM-SHA384:DHE-RSA-AES256-GCM-SHA384"

ssl cipher dtlsv1 custom "AES256-SHA"

ssl cipher tlsv1.2 custom "ECDHE-RSA-AES256-GCM-SHA384:DHE-RSA-AES256-GCM-SHA384"

ssl cipher dtlsv1.2 custom "ECDHE-RSA-AES256-GCM-SHA384:DHE-RSA-AES256-GCM-SHA384"

ssl ecdh-group group20

ssl dh-group group24

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
Hall of Fame Master

Re: AnyConnect new feature - DTLSv1.2

12 REPLIES
Highlighted
Hall of Fame Master

Re: AnyConnect new feature - DTLSv1.2

Re: AnyConnect new feature - DTLSv1.2

Thank you Marvin!  I've been struggling with this for awhile and of course today the client update is released...

 

Confirmation session output is shown below.

 

DTLS-Tunnel:
Tunnel ID : 10156.3
Assigned IP : y.y.y.y Public IP : x.x.x.x
Encryption : AES-GCM-256 Hashing : SHA384
Ciphersuite : ECDHE-RSA-AES256-GCM-SHA384
Encapsulation: DTLSv1.2 UDP Src Port : 53241
UDP Dst Port : 443 Auth Mode : Certificate and userPassword
Idle Time Out: 30 Minutes Idle TO Left : 30 Minutes
Conn Time Out: 1440 Minutes Conn TO Left : 1437 Minutes
Client OS : Windows
Client Type : DTLS VPN Client
Client Ver : Cisco AnyConnect VPN Agent for Windows 4.7.00136

Hall of Fame Master

Re: AnyConnect new feature - DTLSv1.2

I just upgraded my lab - FTD 6.3 (includes LINA / ASA release 9.10(1)3) and pushing AnyConnect 4.7.00136. Note the TLS 1.2 connection:

 

> show vpn-sessiondb detail anyconnect

Session Type: AnyConnect Detailed

Username : user1 Index : 5
Assigned IP : 172.31.1.211 Public IP : 192.168.0.107
Protocol : AnyConnect-Parent SSL-Tunnel DTLS-Tunnel
License : AnyConnect Premium
Encryption : AnyConnect-Parent: (1)none SSL-Tunnel: (1)AES-GCM-256 DTLS-Tunnel: (1)AES256
Hashing : AnyConnect-Parent: (1)none SSL-Tunnel: (1)SHA384 DTLS-Tunnel: (1)SHA1
Bytes Tx : 32022 Bytes Rx : 34713
Pkts Tx : 129 Pkts Rx : 278
Pkts Tx Drop : 0 Pkts Rx Drop : 0
Group Policy : CCIELab_GP Tunnel Group : CCIELab_VPN
Login Time : 03:52:57 UTC Thu Dec 6 2018
Duration : 0h:02m:21s
Inactivity : 0h:00m:00s
VLAN Mapping : N/A VLAN : none
Audt Sess ID : ac1f0101000050005c089d19
Security Grp : none Tunnel Zone : 0

AnyConnect-Parent Tunnels: 1
SSL-Tunnel Tunnels: 1
DTLS-Tunnel Tunnels: 1

AnyConnect-Parent:
Tunnel ID : 5.1
Public IP : 192.168.0.107
Encryption : none Hashing : none 
TCP Src Port : 23728 TCP Dst Port : 443 
Auth Mode : userPassword 
Idle Time Out: 30 Minutes Idle TO Left : 27 Minutes 
Client OS : win 
Client OS Ver: 10.0.17134 
Client Type : AnyConnect
Client Ver : Cisco AnyConnect VPN Agent for Windows 4.7.00136
Bytes Tx : 8454 Bytes Rx : 0 
Pkts Tx : 6 Pkts Rx : 0 
Pkts Tx Drop : 0 Pkts Rx Drop : 0 

SSL-Tunnel:
Tunnel ID : 5.2
Assigned IP : 172.31.1.211 Public IP : 192.168.0.107
Encryption : AES-GCM-256 Hashing : SHA384 
Ciphersuite : ECDHE-RSA-AES256-GCM-SHA384 
Encapsulation: TLSv1.2 TCP Src Port : 23732 
TCP Dst Port : 443 Auth Mode : userPassword 
Idle Time Out: 30 Minutes Idle TO Left : 27 Minutes 
Client OS : Windows 
Client Type : SSL VPN Client
Client Ver : Cisco AnyConnect VPN Agent for Windows 4.7.00136
Bytes Tx : 8454 Bytes Rx : 496 
Pkts Tx : 6 Pkts Rx : 5 
Pkts Tx Drop : 0 Pkts Rx Drop : 0 

DTLS-Tunnel:
Tunnel ID : 5.3
Assigned IP : 172.31.1.211 Public IP : 192.168.0.107
Encryption : AES256 Hashing : SHA1 
Ciphersuite : DHE-RSA-AES256-SHA 
Encapsulation: DTLSv1.0 UDP Src Port : 51520 
UDP Dst Port : 443 Auth Mode : userPassword 
Idle Time Out: 30 Minutes Idle TO Left : 29 Minutes 
Client OS : Windows 
Client Type : DTLS VPN Client
Client Ver : Cisco AnyConnect VPN Agent for Windows 4.7.00136
Bytes Tx : 15114 Bytes Rx : 34217 
Pkts Tx : 117 Pkts Rx : 273 
Pkts Tx Drop : 0 Pkts Rx Drop : 0 

> show running-config ssl
ssl server-version tlsv1.2
ssl cipher tlsv1.2 high
ssl dh-group group1
ssl trust-point VPN_Cert_Enrollment
ssl trust-point VPN_Cert_Enrollment Outside-Home
>
> show version
---------[ vftd-new.ccielab.mrneteng.com ]----------
Model : Cisco Firepower Threat Defense for VMWare (75) Version 6.3.0 (Build 83)
UUID : 69c94e8a-92d2-11e7-b4ad-db36033706e7
Rules update version : 2018-12-03-001-vrt
VDB version : 307
----------------------------------------------------

> system support diagnostic-cli
Attaching to Diagnostic CLI ... Press 'Ctrl+a then d' to detach.
Type help or '?' for a list of available commands.

vftd-new> show ver
vftd-new> show version
---------[ vftd-new.ccielab.mrneteng.com ]----------
Model : Cisco Firepower Threat Defense for VMWare (75) Version 6.3.0 (Build 83)
UUID : 69c94e8a-92d2-11e7-b4ad-db36033706e7
Rules update version : 2018-12-03-001-vrt
VDB version : 307
----------------------------------------------------

Cisco Adaptive Security Appliance Software Version 9.10(1)3
Firepower Extensible Operating System Version 2.4(1.216)

Compiled on Tue 27-Nov-18 12:00 PST by builders
System image file is "boot:/asa9101-3-smp-k8.bin"
Config file at boot was "startup-config"

vftd-new up 1 hour 0 mins

Hardware: ASAv, 8192 MB RAM, CPU Pentium II 2100 MHz, 1 CPU (4 cores)
Model Id: ASAv30
Internal ATA Compact Flash, 50176MB
Slot 1: ATA Compact Flash, 50176MB
BIOS Flash Firmware Hub @ 0x0, 0KB


0: Int: Internal-Data0/0 : address is 000c.2924.8e3e, irq 10
1: Ext: GigabitEthernet0/0 : address is 000c.2924.8e48, irq 5
2: Ext: GigabitEthernet0/1 : address is 000c.2924.8e52, irq 9
3: Ext: GigabitEthernet0/2 : address is 000c.2924.8e5c, irq 11
4: Int: Internal-Control0/0 : address is 0000.0001.0001, irq 0
5: Int: Internal-Data0/0 : address is 0000.0000.0000, irq 0
6: Ext: Management0/0 : address is 000c.2924.8e3e, irq 0
7: Int: Internal-Data0/1 : address is 0000.0000.0000, irq 0
8: Int: Internal-Data0/2 : address is 0000.0000.0000, irq 0

Serial Number: 9ADK32SQAT2

Image type : Release
Key version : A

Configuration last modified by enable_1 at 03:41:24.871 UTC Thu Dec 6 2018
vftd-new>

 

Beginner

Re: AnyConnect new feature - DTLSv1.2

Marvin, the config print out from your lab lists the the DTLS tunnel as using TLS 1.1  and SHA1. Was this an oversite in the thread?

Solved: Re: AnyConnect new feature - DTLSv1.2 - Cisco Community

DTLS-Tunnel:
Tunnel ID : 5.3
Assigned IP : 172.31.1.211 Public IP : 192.168.0.107
Encryption : AES256 Hashing : SHA1 
Ciphersuite : DHE-RSA-AES256-SHA 
Encapsulation: DTLSv1.0 UDP Src Port : 51520 
UDP Dst Port : 443 Auth Mode : userPassword 
Idle Time Out: 30 Minutes Idle TO Left : 29 Minutes 
Client OS : Windows 
Client Type : DTLS VPN Client
Client Ver : Cisco AnyConnect VPN Agent for Windows 4.7.00136
Bytes Tx : 15114 Bytes Rx : 34217 
Pkts Tx : 117 Pkts Rx : 273 
Pkts Tx Drop : 0 Pkts Rx Drop : 0 

Hall of Fame Master

Re: AnyConnect new feature - DTLSv1.2

I noticed that. TLS is 1.2, DTLS is not.

 

I'm wondering if it's FTD vs. ASA thing. I need to upgrade my ASAv to 9.10(1) and compare.

Beginner

Re: AnyConnect new feature - DTLSv1.2

I have scanned the requirements. Anyconnect 4.7 is required to enable TLS1.2. Do you also have to have a ECDHE Public Certificate?  I am a little confused. There is a requirement for cipher strength in the documentation that I saw. Is this the case? 'ECDHE-RSA-AES256-GCM-SHA384:DHE-RSA-AES256-GCM-SHA384'

Re: AnyConnect new feature - DTLSv1.2

From what I've seen, ciphers that start with ECDHE-RSA do not require an EC certificate.  Ciphers that start with ECDHE-ECDSA do.

Beginner

Re: AnyConnect new feature - DTLSv1.2

I am going to load v9.10.1 on one production 5525 this weekend to test out compatibility, I was wondering if any version of Anyconnect 4.x will work with the release? Currently running 4.6.3 and tested AC 4.7 on one machine. We don't have a lab. This ASA is not a busy as others.
We are using Machine Certs and RSA SDI prox-ied thru ISE. In essence just username and password (RSA) with Machine Certificate Authentication. Our AC client is v4.4.03034. This should work just fine? Is this also the case? (I am little hesitant about it)
If v4.6.02074 works I don't see why not? ?
-> 'With the release of v9.10.1, has anyone been able to get DTLSv1.2 working with AnyConnect sessions? (Our clients are v4.6.02074)'

Thanks for the Help to all!

Re: AnyConnect new feature - DTLSv1.2

We were using v4.2 clients with v9.9 ASA code.  I don't see 9.10.1 code as having a problem with older client versions.  It's more like older client versions don't support more recently implemented features.  If you are doing the same things, it shouldn't be a problem...but always test.

Cisco Employee

Re: AnyConnect new feature - DTLSv1.2

I have tested ASA 9.10.1 with AnyConnect 4.7 and TLS 1.2.  Connection comes up and shows correct DTLS version.  as noted by others 4.7 is required for DTLS 1.2.  Previous version of AnyConnect will work with this version of ASA, but will not connect with DTLS 1.2.

 

ASA-9-10-1.PNGdtls-1-2.PNG

Beginner

Re: AnyConnect new feature - DTLSv1.2

This new thread denotes a possible MTU bug with the new client. Has any one else seen this?

https://community.cisco.com/t5/vpn-and-anyconnect/anyconnect-4-7-00136-significant-mtu-bug/m-p/3764323

javentre Beginner
Beginner
‎12-15-2018 06:34 AM
AnyConnect 4.7.00136 - Significant MTU bug

There is a fairly major bug in AnyConnect 4.7.00136 regarding the tunnel MTU. If DTLS is enabled, it will send packets that are too big and many applications break. Ignoring the df-bit and/or specifying a low MTU doesn't workaround the issue. Disabling DTLS is the only workaround.

Syslog may show a flood of errors like this, where the packet is most often 16 bytes larger than the threshold.:

14 Dec 08 2018 20:06:33 722035 Group <ar-6> User <IC005654> IP <198.18.3.45> Received large packet 1276 (threshold 1260).

Re: AnyConnect new feature - DTLSv1.2

Thanks arnert, that's good to know!  There is also an LDAP bug in 9.10.1 we're seeing that causes ASA to crash.  It's not published yet, but if you use LDAP to authenticate users I'd suggest not upgrading yet.

CreatePlease to create content
Ask the Expert- Introduction to Network Design