cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2827
Views
0
Helpful
3
Replies

bri ISDN data call

gljames
Level 1
Level 1

I am replacing an cisco 1601 ISDN router (wich is working) with a cisco 1841 (with a Wic-1B-S/T-v3 ISDN card installed

the config (including userid & password) have been copied over

When tested the ISDN link attempts to come up then fails with a cause code of 16

the following is a debug of the ISDN

The config of the router is

F1EBMWISDN-01#show run

Building configuration...

Current configuration : 4518 bytes

!

version 15.0

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

hostname F1EBMWISDN-01

!

boot-start-marker

boot-end-marker

!

logging buffered 51200 warnings

enable secret 5 $1$I3Sw$rmt0vWQ.JPE8aEWQGLMyz.

enable password 7 09601A3B1608121D

!

aaa new-model

!

!

aaa group server tacacs+ UNI

server 160.3.16.81

!

aaa authentication login default group UNI local

aaa authentication enable default group UNI enable

aaa accounting exec default

action-type start-stop

group UNI

!

aaa accounting commands 15 default

action-type stop-only

group UNI

!

!

!

!

!

!

aaa session-id common

no ip source-route

!

!

!

!

ip cef

multilink bundle-name authenticated

isdn switch-type basic-net3

!

!

license udi pid CISCO1841 sn FCZ1519C3XT

username nw-admin password 7 113E18091201595C557A

!

!

!

!

!

!

interface FastEthernet0/0

description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-FE 0$

ip address 192.168.244.4 255.255.255.0

no ip redirects

ip nat inside

ip virtual-reassembly

no ip route-cache cef

no ip route-cache

duplex auto

speed auto

no cdp enable

standby 253 ip 192.168.244.6

standby 253 timers 5 15

standby 253 priority 201

standby 253 preempt

!

interface FastEthernet0/1

no ip address

shutdown

duplex auto

speed auto

!

interface BRI0/0/0

description Connects to

no IP address

encapsulation ppp

no ip route-cache cef

no ip route-cache

dialer pool-member 1

isdn switch-type basic-net3

isdn point-to-point-setup

ppp multilink

no cdp enable

!

interface Dialer1

ip address negotiated

ip nat outside

no ip virtual-reassembly

encapsulation ppp

dialer pool 1

dialer remote-name ASACC1

dialer string 00498935474900

dialer load-threshold 3 outbound

dialer-group 1

ppp authentication chap

ppp chap hostname spabuees

ppp chap password 7 072A297B7C004A3344

ppp multilink

!

ip forward-protocol nd

!

!

ip http server

ip http access-class 23

ip http authentication local

ip http timeout-policy idle 60 life 86400 requests 10000

ip nat inside source static 10.201.80.204 160.48.223.41

ip route 0.0.0.0 0.0.0.0 192.168.244.1

ip route 160.48.223.41 255.255.255.255 Dialer1

ip route 160.50.6.48 255.255.255.255 Dialer1

ip route 172.25.195.107 255.255.255.255 Dialer1

ip tacacs source-interface FastEthernet0/0

!

access-list 100 permit ip host 160.48.223.41 any

access-list 100 permit ip host 10.201.80.204 any

dialer-list 1 protocol ip permit

!

tacacs-server host 160.3.16.81

tacacs-server directed-request

!

control-plane

!

!

line con 0

line aux 0

line vty 0 4

access-class 23 in

privilege level 15

transport input telnet

line vty 5 15

access-class 23 in

privilege level 15

transport input telnet

!

scheduler allocate 20000 1000

end

F1EBMWISDN-01#

*Jul 11 13:34:47.731: ISDN BR0/0/0 EVENT: UserIdle: callid 0x8003 received ISDN_CALL (0x0)

*Jul 11 13:34:47.731: ISDN BR0/0/0 EVENTd: UserIdle: Call to 00498935474900 at 64 Kb/s

*Jul 11 13:34:47.731: ISDN BR0/0/0 EVENTd: isdn_get_guid: Cannot allocate a GUID (5)

*Jul 11 13:34:47.731: ISDN BR0/0/0 EVENT: process_bri_call: call id 0x8003, called_number 00498935474900, Guid 00740000FFFF speed 64, call type DATA, bchan -1 clng_e

*Jul 11 13:34:47.731: ISDN BR0/0/0 EVENTd: process_bri_call: No name in GTD

*Jul 11 13:34:47.731: ISDN BR0/0/0 EVENTd: calltrkr_setup_received: isdn_info=1675789144l, call_id=0x8003 ORIGINATE

*Jul 11 13:34:47.731: ISDN BR0/0/0 EVENTd: calltrkr_setup_received: calltracker disabled

*Jul 11 13:34:47.731: ISDN BR0/0/0 Q931: Sending SETUP callref = 0x0003 callID = 0x8003 switch = basic-net3 interface = User

*Jul 11 13:34:47.731: ISDN BR0/0/0 Q931: TX -> SETUP pd = 8 callref = 0x03

Bearer Capability i = 0x8890

Standard = CCITT

Transfer Capability = Unrestricted Digital

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0x81

Preferred, B1

Called Party Number i = 0x80, '00498935474900'

Plan:Unknown, Type:Unknown

*Jul 11 13:34:47.935: ISDN BR0/0/0 Q931: RX <- SETUP_ACK pd = 8 callref = 0x83

Channel ID i = 0x89

Exclusive, B1

Progress Ind i = 0x8288 - In-band info or appropriate now available

*Jul 11 13:34:47.935: ISDN BR0/0/0 EVENT: process_rxstate: ces/callid 1/0x8003 calltype 1 HOST_INFORMATION

*Jul 11 13:34:47.935: ISDN BR0/0/0 EVENTd: host_information: call id 0x8003 b channel 0 assigned by switch

*Jul 11 13:34:54.027: ISDN BR0/0/0 Q931: RX <- CALL_PROC pd = 8 callref = 0x83

*Jul 11 13:34:54.027: ISDN BR0/0/0 EVENT: process_rxstate: ces/callid 1/0x8003 calltype 1 HOST_PROCEEDING

*Jul 11 13:34:54.027: ISDN BR0/0/0 EVENTd: host_more_info: B-channel assigned in previous message call id 0x8003

*Jul 11 13:34:54.059: ISDN BR0/0/0 Q931: RX <- CONNECT pd = 8 callref = 0x83

*Jul 11 13:34:54.059: ISDN BR0/0/0 EVENT: process_rxstate: ces/callid 1/0x8003 calltype 1 HOST_CONNECT

*Jul 11 13:34:54.059: ISDN BR0/0/0 EVENTd: isdn_report: callid 0x8003

*Jul 11 13:34:54.059: %LINK-3-UPDOWN: Interface BRI0/0/0:1, changed state to up

*Jul 11 13:34:54.063: %DIALER-6-BIND: Interface BR0/0/0:1 bound to profile Di1

*Jul 11 13:34:54.063: %ISDN-6-CONNECT: Interface BRI0/0/0:1 is now connected to 00498935474900 N/A

*Jul 11 13:34:54.063: ISDN BR0/0/0 EVENTd: isdn_mib_update: Update Charge Units 0 hndl=0

*Jul 11 13:34:54.063: ISDN BR0/0/0 EVENTd: calltrkr_call_connect: isdn_info=0x63E2AB44, call_id=0x8003

*Jul 11 13:34:54.063: ISDN BR0/0/0 EVENTd: calltrkr_call_connect: hndl=0l, cntrl_slot=0, cntrl_port=0, cntrl_channel=0.

*Jul 11 13:34:54.063: ISDN BR0/0/0 EVENTd: host_connect: Connected to 00498935474900 on B1 at 64 Kb/s

*Jul 11 13:34:54.067: ISDN BR0/0/0 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x03

*Jul 11 13:34:55.311: ISDN BR0/0/0 EVENT: UserIdle: callid 0x8003 received ISDN_HANGUP (0x1)

*Jul 11 13:34:55.315: ISDN BR0/0/0 EVENT: isdn_hangup: Hangup call to call id 0x8003 ces = 1

*Jul 11 13:34:55.315: ISDN BR0/0/0 EVENTd: process_disconnect: call id 0x8003, call type is DATA, b_idb 0x63E29788, ces 1, cause Normal call clearing(0x10)

*Jul 11 13:34:55.315: %ISDN-6-DISCONNECT: Interface BRI0/0/0:1 disconnected from 00498935474900 asacc1, call lasted 1 seconds

*Jul 11 13:34:55.315: ISDN BR0/0/0 EVENTd: isdn_mib_update: Update Charge Units 0 hndl=0

*Jul 11 13:34:55.315: ISDN BR0/0/0 EVENTd: calltrkr_call_disconnected: isdn_info=0x63E2AB44, call_id=0x8003

*Jul 11 13:34:55.315: ISDN BR0/0/0 EVENTd: calltrkr_call_disconnected: hndl=0l, cause=16, Normal call clearing

*Jul 11 13:34:55.315: ISDN BR0/0/0 EVENTd: process_disconnect: Raw Release Message

*Jul 11 13:34:55.315: 0500018003040802FF9008028090

*Jul 11 13:34:55.315: ISDN BR0/0/0 Q931: TX -> DISCONNECT pd = 8 callref = 0x03

Cause i = 0x8090 - Normal call clearing

*Jul 11 13:34:55.495: ISDN BR0/0/0 Q931: RX <- RELEASE pd = 8 callref = 0x83

*Jul 11 13:34:55.495: ISDN EVENTd: cc_clear_free_list freeing 0x63E8CA80

*Jul 11 13:34:55.495: ISDN BR0/0/0 EVENT: process_rxstate: ces/callid 1/0x8003 calltype 1 HOST_DISCONNECT_ACK

*Jul 11 13:34:55.495: ISDN BR0/0/0 EVENTd: calltrkr_call_cleared: isdn_info=0x63E28358, call_id=0x8003

*Jul 11 13:34:55.495: ISDN BR0/0/0 EVENTd: calltrkr_call_cleared: isdn_info=0x63E2AB44, call_id=0x8003

*Jul 11 13:34:55.495: ISDN BR0/0/0 EVENTd: calltrkr_call_cleared: hndl=0, cause=16, Normal call clearing

*Jul 11 13:34:55.495: ISDN BR0/0/0 EVENTd: calltrkr_call_cleared: isdn_info=0x63E2AB44, call_id=0x8003

*Jul 11 13:34:55.495: ISDN BR0/0/0 EVENTd: calltrkr_call_cleared: isdn_info=0x63E28358, call_id=0x8003

*Jul 11 13:34:55.495: ISDN BR0/0/0 EVENTd: host_disconnect_ack: call type is DATA

*Jul 11 13:34:55.495: %LINK-3-UPDOWN: Interface BRI0/0/0:1, changed state to down

*Jul 11 13:34:55.499: %DIALER-6-UNBIND: Interface BR0/0/0:1 unbound from profile Di1

*Jul 11 13:34:55.499: ISDN BR0/0/0 EVENTd: isdn_report: callid 0x8003

*Jul 11 13:34:55.499: ISDN BR0/0/0 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x03

*Jul 11 13:34:57.359: ISDN BR0/0/0 EVENT: UserIdle: callid 0x8004 received ISDN_CALL (0x0)

*Jul 11 13:34:57.359: ISDN BR0/0/0 EVENTd: UserIdle: Call to 00498935474900 at 64 Kb/s

*Jul 11 13:34:57.359: ISDN BR0/0/0 EVENTd: isdn_get_guid: Cannot allocate a GUID (5)

*Jul 11 13:34:57.359: ISDN BR0/0/0 EVENT: process_bri_call: call id 0x8004, called_number 00498935474900, Guid 00740000FFFF speed 64, call type DATA, bchan -1 clng_e

*Jul 11 13:34:57.359: ISDN BR0/0/0 EVENTd: process_bri_call: No name in GTD

*Jul 11 13:34:57.363: ISDN BR0/0/0 EVENTd: calltrkr_setup_received: isdn_info=1675789144l, call_id=0x8004 ORIGINATE

*Jul 11 13:34:57.363: ISDN BR0/0/0 EVENTd: calltrkr_setup_received: calltracker disabled

*Jul 11 13:34:57.363: ISDN BR0/0/0 Q931: Sending SETUP callref = 0x0004 callID = 0x8004 switch = basic-net3 interface = User

*Jul 11 13:34:57.363: ISDN BR0/0/0 Q931: TX -> SETUP pd = 8 callref = 0x04

Bearer Capability i = 0x8890

Standard = CCITT

Transfer Capability = Unrestricted Digital

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0x81

Preferred, B1

Called Party Number i = 0x80, '00498935474900'

Plan:Unknown, Type:Unknown

*Jul 11 13:34:57.535: ISDN BR0/0/0 Q931: RX <- SETUP_ACK pd = 8 callref = 0x84

Channel ID i = 0x89

Exclusive, B1

Progress Ind i = 0x8288 - In-band info or appropriate now available

*Jul 11 13:34:57.535: ISDN BR0/0/0 EVENT: process_rxstate: ces/callid 1/0x8004 calltype 1 HOST_INFORMATION

*Jul 11 13:34:57.535: ISDN BR0/0/0 EVENTd: host_information: call id 0x8004 b channel 0 assigned by switch

1 Accepted Solution

Accepted Solutions

paolo bevilacqua
Hall of Fame
Hall of Fame

Take debug ppp neg, debug ppp auth.

Do not take any other debug.

View solution in original post

3 Replies 3

paolo bevilacqua
Hall of Fame
Hall of Fame

Take debug ppp neg, debug ppp auth.

Do not take any other debug.

Identified that the difference in the IOS dictated that the "Callin" parameter was required on the PPP Chap authentication statement on the Dialer 1 interface, this prevents the remote router trying to authenticate (which wa s the reason the failure was occuring

Thanks

Glyn

Thanks for the nice rating and good luck!

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: