02-05-2014 05:59 AM
Hi
I was wondering is someone can help me with this. I have set up my 2509 access server. I think i have the setting right. When i go to connect to a device the access server just hangs. I do a ctrl+shift 6 x and it lets me out. I do a show sessions and it shows i have a session. I do a show line and it says the line is active. I do a show line tty 3 and it shows the line is active. It seems like it is connecting to the remote device ....
Current configuration:
!
version 11.2
service password-encryption
!
hostname TermServer1
!
enable secret 5 $1$65CQ$F3eZiywXSDSwzF.J0FOYp0
!
ip host r1 2003 1.1.1.1
ip host r2851 2001 1.1.1.1
ip host r2500 2002 1.1.1.1
!
interface Loopback0
ip address 1.1.1.1 255.255.255.255
!
interface Ethernet0
no ip address
shutdown
!
interface Serial0
no ip address
shutdown
no fair-queue
!
interface Serial1
no ip address
shutdown
!
no ip classless
!
line con 0
exec-timeout 0 0
password 7 00171B03085912
logging synchronous
login
line 1 8
no exec
exec-timeout 0 0
monitor
transport input telnet
line aux 0
line vty 0 4
exec-timeout 0 0
password 7 120A0D121E0915
login
transport input telnet
!
end
TermServer1#r1
Trying r1 (1.1.1.1, 2003)... Open
TermServer1#show sessions
Conn Host Address Byte Idle Conn Name
* 1 r1 1.1.1.1 0 0 r1
TermServer1#show line
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns
* 0 CTY - - - - - 2 2 0/0
1 TTY 9600/9600 - - - - - 0 0 0/0
2 TTY 9600/9600 - - - - - 0 175 0/0
* 3 TTY 9600/9600 - - - - - 2 61 0/0
4 TTY 9600/9600 - - - - - 0 24 0/0
5 TTY 9600/9600 - - - - - 0 78 0/0
6 TTY 9600/9600 - - - - - 0 70 0/0
7 TTY 9600/9600 - - - - - 0 0 0/0
8 TTY 9600/9600 - - - - - 0 30 0/0
9 AUX 9600/9600 - - - - - 0 0 0/0
10 VTY - - - - - 0 0 0/0
11 VTY - - - - - 0 0 0/0
12 VTY - - - - - 0 0 0/0
13 VTY - - - - - 0 0 0/0
14 VTY - - - - - 0 0 0/0
TermServer1#show line tty 3
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns
* 3 TTY 9600/9600 - - - - - 2 61 0/0
Line 3, Location: "", Type: ""
Length: 24 lines, Width: 80 columns
Baud rate (TX/RX) is 9600/9600, no parity, 2 stopbits, 8 databits
Status: Ready, Connected, Active
Capabilities: EXEC Suppressed, Receives Logging Output
Modem state: Ready
Special Chars: Escape Hold Stop Start Disconnect Activation
^^x none - - none
Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch
never never none not set
Idle Session Disconnect Warning
never
Modem type is unknown.
Session limit is not set.
Time since activation: never
Editing is enabled.
History is enabled, history size is 10.
Full user help is disabled
Allowed transports are pad v120 telnet rlogin. Preferred is telnet.
No output characters are padded
No special data dispatching characters
Modem hardware state: CTS DSR DTR RTS
TermServer1#
any help with this would be great
Thanks
Kel
02-09-2014 05:30 AM
Kel
The thing that I notice on the async lines is this command
monitor
I do not usually see this in term server configs. I am not sure that it is the problem. But I would suggest that you remove it and see if the behavior changes.
HTH
Rick
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: