VTI-based EZVPN remote client

johnlloyd_13 · ‎01-31-2013

hi all,

i've been troubleshooting my EZVPN lab setup but can't seem to make it work.

appreciate someone's help with my config. thanks in advance!

EZVPN_SERVER#sh ip int bri

Interface IP-Address OK? Method Status Protocol

FastEthernet0/0 1.1.1.1 YES manual up up

FastEthernet0/1 unassigned YES unset administratively down down

FastEthernet1/0 unassigned YES unset administratively down down

Virtual-Access1 unassigned YES unset down down

Virtual-Template1 1.1.1.1 YES TFTP down down

Loopback1 172.16.2.10 YES manual up up

EZVPN_SERVER#show run

Building configuration...

Current configuration : 2281 bytes

!

version 12.4

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname EZVPN_SERVER

!

boot-start-marker

boot-end-marker

!

aaa new-model

!

aaa authentication login EZVPN_AUTHENTICATION local

aaa authorization network EZVPN_AUTHORIZTION local

!

aaa session-id common

!

resource policy

!

memory-size iomem 5

ip subnet-zero

ip cef

!

no ip domain lookup

ip domain name lab.local

!

username ezvpnuser password 0 cisco

!

crypto isakmp policy 10

encr aes

authentication pre-share

group 5

!

crypto isakmp client configuration group EZVPN_GROUP

key cisco

domain lab.com

pool EZVPN_POOL

acl EZVPN_SPLIT_TUNNEL_ACL

crypto isakmp profile EZVPN_ISAKMP_PROFILE

match identity group EZVPN_GROUP

client authentication list EZVPN_AUTHENTICATION

isakmp authorization list EZVPN_AUTHORIZATION

client configuration address respond

client configuration group EZVPN_GROUP

virtual-template 1

!

crypto ipsec transform-set EZVPN_TSET esp-aes esp-sha-hmac

!

crypto ipsec profile EZVPN_IPSEC_PROFILE

set transform-set EZVPN_TSET

set isakmp-profile EZVPN_ISAKMP_PROFILE

!

interface Loopback1

ip address 172.16.2.10 255.255.255.0

!

interface FastEthernet0/0

ip address 1.1.1.1 255.255.255.252

duplex auto

speed auto

!

interface FastEthernet0/1

no ip address

shutdown

duplex auto

speed auto

!

interface FastEthernet1/0

no ip address

shutdown

duplex auto

speed auto

!

interface Virtual-Template1 type tunnel

ip unnumbered FastEthernet0/0

tunnel mode ipsec ipv4

tunnel protection ipsec profile EZVPN_IPSEC_PROFILE

!

ip local pool EZVPN_POOL 172.16.100.10 172.16.100.150

ip classless

ip route 0.0.0.0 0.0.0.0 1.1.1.2

!

no ip http server

no ip http secure-server

!

ip access-list extended EZVPN_SPLIT_TUNNEL_ACL

permit ip 172.16.2.0 0.0.0.255 any

!

control-plane

!

line con 0

exec-timeout 0 0

privilege level 15

logging synchronous

line aux 0

exec-timeout 0 0

privilege level 15

logging synchronous

line vty 0 4

!

end

-----

EZVPN_CLIENT#show ip interface brief

Interface IP-Address OK? Method Status Protocol

FastEthernet0/0 1.1.1.2 YES manual up up

FastEthernet0/1 172.16.1.254 YES manual up up

FastEthernet1/0 unassigned YES unset administratively down down

Virtual-Access1 unassigned YES unset down down

Virtual-Template1 unassigned YES TFTP down down

Virtual-TokenRing1 unassigned YES unset up up

EZVPN_CLIENT#show run

Building configuration...

Current configuration : 1355 bytes

!

version 12.4

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname EZVPN_CLIENT

!

boot-start-marker

boot-end-marker

!

no aaa new-model

!

resource policy

!

memory-size iomem 5

ip subnet-zero

ip cef

!

no ip domain lookup

ip domain name lab.local

!

crypto ipsec client ezvpn EZVPN_CLIENT

connect auto

group EZVPN_GROUP key cisco

mode client

peer 1.1.1.1

username ezvpnuser password cisco

xauth userid mode local

!

interface FastEthernet0/0

ip address 1.1.1.2 255.255.255.252

duplex auto

speed auto

!

interface FastEthernet0/1

ip address 172.16.1.254 255.255.255.0

duplex auto

speed auto

crypto ipsec client ezvpn EZVPN_CLIENT inside

!

interface FastEthernet1/0

no ip address

shutdown

duplex auto

speed auto

!

interface Virtual-Template1 type tunnel

no ip address

tunnel mode ipsec ipv4

crypto ipsec client ezvpn EZVPN_CLIENT

!

ip classless

ip route 0.0.0.0 0.0.0.0 1.1.1.1

!

no ip http server

no ip http secure-server

!

control-plane

!

line con 0

exec-timeout 0 0

privilege level 15

logging synchronous

line aux 0

exec-timeout 0 0

privilege level 15

logging synchronous

line vty 0 4

login

!

end

----

EZVPN_CLIENT#show crypto isakmp sa

dst src state conn-id slot status

1.1.1.1 1.1.1.2 AG_INIT_EXCH 1 0 ACTIVE

EZVPN_CLIENT#show crypto ipsec client ezvpn

Easy VPN Remote Phase: 4

Tunnel name : EZVPN_CLIENT

Inside interface list: FastEthernet0/1

Outside interface: Virtual-Template1

Current State: VALID_CFG

Last Event: VALID_CONFIG_ENTERED

Save Password: Allowed

Current EzVPN Peer: 1.1.1.1

EZVPN_CLIENT(config-if)#

*Mar 1 01:51:33.835: EZVPN(EZVPN_CLIENT): Current State: READY

*Mar 1 01:51:33.835: EZVPN(EZVPN_CLIENT): Event: RESET

*Mar 1 01:51:33.835: EZVPN(EZVPN_CLIENT): New active peer is 1.1.1.1

*Mar 1 01:51:33.835: EZVPN(EZVPN_CLIENT): Ready to connect to peer 1.1.1.1

*Mar 1 01:51:33.835: EZVPN(EZVPN_CLIENT): ezvpn_close

*Mar 1 01:51:33.835: EZVPN(EZVPN_CLIENT): Deleted PSK for address 1.1.1.1

*Mar 1 01:51:33.835: %CRYPTO-6-EZVPN_CONNECTION_DOWN: (Client) User= Group=EZVPN_GROUP

Client_public_addr=1.1.1.2 Server_public_addr=1.1.1.1

*Mar 1 01:51:33.835: EZVPN(EZVPN_CLIENT): ezvpn_reset

*Mar 1 01:51:33.835: EZVPN(EZVPN_CLIENT): New State: CONNECT_REQUIRED

*Mar 1 01:51:33.835: EZVPN(EZVPN_CLIENT): Current State: CONNECT_REQUIRED

*Mar 1 01:51:33.835: EZVPN(EZVPN_CLIENT): Event: CONNECT

*Mar 1 01:51:33.835: EZVPN(EZVPN_CLIENT): ezvpn_connect_request

*Mar 1 01:51:33.835: EZVPN(EZVPN_CLIENT): Found valid peer 1.1.1.1

*Mar 1 01:51:33.835: EZVPN(EZVPN_CLIENT): Added PSK for address 1.1.1.1

*Mar 1 01:51:33.835: EZVPN(EZVPN_CLIENT): New State: READY

*Mar 1 01:51:33.835: ISAKMP: received ke message (1/1)

*Mar 1 01:51:33.835: ISAKMP:(0:1:SW:1):SA is still budding. Attached new ipsec request to it. (local

1.1.1.2, remote 1.1.1.1)

amoljunghare · ‎01-31-2013

Command missing on client outside interface that is fa 0/0

Crypto ipsec client ezvpn .....

....outside.

Sent from Cisco Technical Support Android App

johnlloyd_13 · ‎02-01-2013

hi,

thanks for the reply! i've tried testing on both FE0/0 (WAN) and virtual-template ports but it's still not working.

i've noticed it's not applying the command as per show run and show ip interface brief shows virtual template as down/down. any ideas?

EZVPN_CLIENT(config)#interface fastethernet0/0

EZVPN_CLIENT(config-if)#crypto ipsec client ezvpn EZVPN_CLIENT ?

inside inside

outside outside

EZVPN_CLIENT(config-if)#crypto ipsec client ezvpn EZVPN_CLIENT outside

Error:Only one outside interface is allowed per ezvpn configuration

malshbou · ‎02-01-2013

Hi,

you missed this command: "virtual-interface 1" under "crypto ipsec client ezvpn EZVPN_CLIENT"

Also, remove "crypto ipsec client ezvpn EZVPN_CLIENT" from under virtual-template interface and put it under the egress physical interface.

i hope this helps you.

----------------------------

Mashal

------------------ Mashal Shboul

johnlloyd_13 · ‎02-03-2013

Hi Mashal,

Thanks for your feedback! Let me lab this again and let you know the results.

Sent from Cisco Technical Support iPad App

johnlloyd_13 · ‎02-05-2013

hi mashal,

i tried to attemp to setup EZVPN again, but i don't see the option for 'virtual-interface 1' command. any ideas and what IOS train has this command?

EZVPN_CLIENT(config-crypto-ezvpn)#?

Crypto EzVPN configuration commands:

acl Specify access-list identifier for SA establishment

backup Configure an EzVPN as a backup

connect Connect

exit Exit from EzVPN configuration mode

group Group Name

local-address Interface to use for local address for this ezvpn

configuration

mode Mode

no Negate a command or set its defaults

peer Allowed Encryption/Decryption Peer

username User Name

xauth XAuth parameters

EZVPN_CLIENT(config-crypto-ezvpn)#v?

% Unrecognized command

EZVPN_CLIENT(config-if)#int f0/0

EZVPN_CLIENT(config-if)#crypto ipsec client ezvpn EZVPN_CLIENT

EZVPN_CLIENT(config-if)#

*Mar 1 00:25:01.079: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is ON

*Mar 1 00:25:01.551: %CRYPTO-6-IKMP_MODE_FAILURE: Processing of Informational mode failed with peer at

1.1.1.1

EZVPN_CLIENT(config-if)#do sh crypto isa sa

dst src state conn-id slot status

1.1.1.1 1.1.1.2 AG_INIT_EXCH 1 0 ACTIVE

stujackson · ‎06-06-2013

Hi John,

Did you resolve this as I have exact same issue. I cannot enter the 'virtual-interface 1' command under "crypto ipsec client ezvpn EZVPN_CLIENT".....any ideas anyone?

I am following the SECURE Offical cert guide, and i have tried this on various router platforms but no joy with that command?

guibarati · ‎06-06-2013

Working sample:

Server:

!

aaa new-model

!

aaa authentication login NO none

aaa authentication login XAUTH local

aaa authentication login XAUTH_EXT group radius

aaa authorization network EZ_POL local

aaa authorization network EZ_EXT group radius

aaa authorization network EZ_PKI group radius

!

aaa session-id common

memory-size iomem 15

clock timezone GMT+1 1

!

dot11 syslog

ip source-route

!

ip cef

!

ip domain name ipexpert.com

no ipv6 cef

!

multilink bundle-name authenticated

!

voice-card 0

!

crypto pki trustpoint CA

enrollment url http://8.9.50.2:80

subject-name cn=R4.ipexpert.com

revocation-check none

authorization username subjectname commonname

!

crypto pki certificate chain CA

certificate 05

30820217 30820180 A0030201 02020105 300D0609 2A864886 F70D0101 04050030

11310F30 0D060355 04030C06 494F535F 4341301E 170D3039 31313035 31313131

30345A17 0D313031 31303531 31313130 345A303A 31183016 06035504 03130F52

342E6970 65787065 72742E63 6F6D311E 301C0609 2A864886 F70D0109 02160F52

342E6970 65787065 72742E63 6F6D305C 300D0609 2A864886 F70D0101 01050003

4B003048 0241009F 721482CA E129C682 DD0DDCE1 11E5247C D25928F4 944E46B1

202A0B37 6058914C F9544B24 C575A54D 93AAA4A8 F2704C8F 50B72CAA C686330B

231D421F 3FE3AF02 03010001 A3819930 81963047 0603551D 1F044030 3E303CA0

3AA03886 36687474 703A2F2F 382E392E 35302E32 2F636769 2D62696E 2F706B69

636C6965 6E742E65 78653F6F 70657261 74696F6E 3D476574 43524C30 0B060355

1D0F0404 030205A0 301F0603 551D2304 18301680 14A8EE2C F39B1E89 A078632E

424AA210 DDAD498B B5301D06 03551D0E 04160414 F7C8467B E42282DD DBDD4557

7654F340 FFBDC6FC 300D0609 2A864886 F70D0101 04050003 81810046 497BAE40

B6FEF229 9ABB1649 B93A0093 94E6A8D7 68841553 AA8E6EA2 FDB87AB1 8E7A819E

FCE4D067 E9D724F6 6B2F4784 01ABDFB0 14FDC760 C794C2CA F307C1C1 FC23ACF0

85629F33 8E8AB07A C48617E9 41C3D9ED 43E204B8 590FDAE1 F894732B DFE1B39D

B8B09CE5 DC9053FC 51713C18 C155E583 3A3EF48D D1DA5FF4 D2747A

quit

certificate ca 01

308201FB 30820164 A0030201 02020101 300D0609 2A864886 F70D0101 04050030

11310F30 0D060355 04030C06 494F535F 4341301E 170D3039 31313034 30383335

31395A17 0D313231 31303330 38333531 395A3011 310F300D 06035504 030C0649

4F535F43 4130819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281

8100B099 9BD61EDF 7EBA0A87 723AEAD4 256D07E1 E04E6BCA F9666A14 95A58D1A

90F649F9 34FDCF71 AA4D969E CBBE2FE5 A50E27F6 3FF0AD7A EC1FD782 9880ECE4

3E0F3AAC F963EC9E C4D44B97 561620AB 0620C646 26729AB2 E88779CB 41F4484F

A5D14F19 BD23A54E 54E84664 90F401B0 1D1E2F1D 99AB3B74 E20DBC25 DED4967C

32A50203 010001A3 63306130 0F060355 1D130101 FF040530 030101FF 300E0603

551D0F01 01FF0404 03020186 301F0603 551D2304 18301680 14A8EE2C F39B1E89

A078632E 424AA210 DDAD498B B5301D06 03551D0E 04160414 A8EE2CF3 9B1E89A0

78632E42 4AA210DD AD498BB5 300D0609 2A864886 F70D0101 04050003 8181001D

C01AC687 4BA19759 3F36946A 14941773 A0678095 35863BF5 085BA8B0 88149A65

663A3729 C2528766 959DFCC8 64C8797E 96711506 64EC97FC AED8A096 D6A78FFA

4CEAF3F1 038B46A0 D5EC9C4A 7D3BAF3E E1B982AB EE2D370B E82715EE 379F436B

A45C7AFA 0637E513 6F0D7CEA 9CB05193 D34F94A4 224627D1 38377926 70956E

quit

!

vtp version 2

username ipexpert password 0 ipexpert

username cciesec password 0 cisco

archive

log config

hidekeys

!

crypto ipsec client ezvpn EZCLIENT

connect manual

group REMOTE key ipexpert

mode client

peer 8.9.50.4

virtual-interface 1

username cciesec password cisco

xauth userid mode local

!

interface Loopback8

ip address 8.8.8.8 255.255.255.0

crypto ipsec client ezvpn EZCLIENT inside

!

interface FastEthernet0/0

no ip address

shutdown

duplex auto

speed auto

!

interface FastEthernet0/1

ip address 192.168.8.8 255.255.255.0

duplex auto

speed auto

crypto ipsec client ezvpn EZCLIENT

!

interface Serial0/0/0

no ip address

shutdown

!

interface Virtual-Template1 type tunnel

ip unnumbered FastEthernet0/1

tunnel mode ipsec ipv4

!

ip forward-protocol nd

ip route 0.0.0.0 0.0.0.0 192.168.8.20

no ip http server

no ip http secure-server

!

control-plane

!

ccm-manager fax protocol cisco

!

mgcp fax t38 ecm

!

line con 0

exec-timeout 0 0

logging synchronous

line aux 0

line vty 0 4

password cisco

login

!

scheduler allocate 20000 1000

end

johnlloyd_13 · ‎06-06-2013

hi,

if i recall correctly, i was able to lab this using a dynamic map instead.

i've used this link as reference:

http://www.labminutes.com/sec0015_router_ezvpn_presharedkey

aijazbeigh · ‎10-06-2013

hi,

it is all configurtaion problems and some time router issues. try reboot as well. Here is working one ezvpn config

SERVER Config

hostname R1

aaa new-model
!
!
aaa authentication login default local
aaa authorization network default local
!

username cisco password 0 cisco
!
redundancy
!!
crypto isakmp policy 3
encr 3des
authentication pre-share
group 2
crypto isakmp xauth timeout 90

!
crypto isakmp client configuration group easy
key cisco
domain foo.com
pool dpool
acl 101
save-password
crypto isakmp profile vi
   match identity group easy
   client authentication list default
   isakmp authorization list default
   client configuration address respond
   client configuration group easy
   virtual-template 1
!
!
crypto ipsec transform-set set esp-3des esp-sha-hmac
!
crypto ipsec profile vi
set transform-set set
set isakmp-profile vi

interface Loopback0
ip address 10.4.0.1 255.255.255.0
!
interface FastEthernet0/0
ip address 7.7.7.1 255.255.255.0
duplex auto
speed auto
!

!
interface Virtual-Template1 type tunnel
ip unnumbered FastEthernet0/0
tunnel mode ipsec ipv4
tunnel protection ipsec profile vi
!
ip local pool dpool 10.5.0.1 10.5.0.10
!
access-list 101 permit ip 10.4.0.0 0.0.0.255 any
!

CLIENT CONFIG

crypto isakmp policy 1

encr 3des

authentication pre-share

group 2

crypto isakmp xauth timeout 5

!

crypto ipsec client ezvpn ez

connect auto

group easy key cisco

mode client

peer 7.7.7.1

virtual-interface 1

username cisco password cisco

xauth userid mode local

!

interface Loopback0

ip address 192.168.1.1 255.255.255.0

crypto ipsec client ezvpn ez inside

!

interface FastEthernet0/0

ip address 7.7.7.2 255.255.255.0

duplex auto

speed auto

crypto ipsec client ezvpn ez

interface Virtual-Template1 type tunnel

no ip address

tunnel mode ipsec ipv4

!

SHOW OUTPUTS

R2#show crypto ipsec client ezvpn

Easy VPN Remote Phase: 6

Tunnel name : ez

Inside interface list: Loopback0

Outside interface: Virtual-Access2 (bound to FastEthernet0/0)

Current State: IPSEC_ACTIVE

Last Event: MTU_CHANGED

Address: 10.5.0.2 (applied on Loopback10000)

Mask: 255.255.255.255

Default Domain: foo.com

Save Password: Allowed

Split Tunnel List: 1

Address : 10.4.0.0

Mask : 255.255.255.0

Protocol : 0x0

Source Port: 0

Dest Port : 0

Current EzVPN Peer: 7.7.7.1

R2#

R2#show ip route

Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2

i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2

ia - IS-IS inter area, * - candidate default, U - per-user static route

o - ODR, P - periodic downloaded static route

Gateway of last resort is 0.0.0.0 to network 0.0.0.0

7.0.0.0/24 is subnetted, 1 subnets

C 7.7.7.0 is directly connected, FastEthernet0/0

10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks

C 10.5.0.2/32 is directly connected, Loopback10000

S 10.4.0.0/24 [1/0] via 0.0.0.0, Virtual-Access2-------------------Split tunnel route

C 192.168.1.0/24 is directly connected, Loopback0

S* 0.0.0.0/0 is directly connected, FastEthernet0/0

R2#show crypto isakmp sa

IPv4 Crypto ISAKMP SA

dst src state conn-id slot status

7.7.7.1 7.7.7.2 QM_IDLE 1001 0 ACTIVE

IPv6 Crypto ISAKMP SA