11-12-2012 11:40 AM
I am trying to configure ASDM on my ASA 5505. I seem to be running into a road block. I get things configured correctly, IP Addressing, VLANs etc.
I can ping my ASA device from the laptop command prompt with no problem.
When I open the browswer and type in https://192.168.10.1 (The IP Address set to E0/1.) I get the Certificate Warning and click continue. I then get a message that the page cannot be found.
I close the browser and reopen it, (cookies, cache and history cleared) and re-type the above IP Address and immediately get the "page not found" message. I can't understand what is going on here as I have accomplished this exact same lab at the college with no problem at all.
Any suggestions?
Thanks,
Steve
FYI...
Here are the results of the show version. I believe I am running a current version.
ASA5505# show ver
Cisco Adaptive Security Appliance Software Version 8.2(4)
Device Manager Version 5.2(4)
Compiled on Tue 14-Dec-10 12:00 by builders
System image file is "disk0:/asa824-k8.bin"
Config file at boot was "startup-config"
ASA5505 up 3 days 23 hours
Hardware: ASA5505, 256 MB RAM, CPU Geode 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
Boot microcode : CN1000-MC-BOOT-2.00
SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.05
0: Int: Internal-Data0/0 : address is 0024.c4c4.b233, irq 11
1: Ext: Ethernet0/0 : address is 0024.c4c4.b22b, irq 255
2: Ext: Ethernet0/1 : address is 0024.c4c4.b22c, irq 255
3: Ext: Ethernet0/2 : address is 0024.c4c4.b22d, irq 255
4: Ext: Ethernet0/3 : address is 0024.c4c4.b22e, irq 255
5: Ext: Ethernet0/4 : address is 0024.c4c4.b22f, irq 255
6: Ext: Ethernet0/5 : address is 0024.c4c4.b230, irq 255
7: Ext: Ethernet0/6 : address is 0024.c4c4.b231, irq 255
8: Ext: Ethernet0/7 : address is 0024.c4c4.b232, irq 255
9: Int: Internal-Data0/1 : address is 0000.0003.0002, irq 255
10: Int: Not used : irq 255
11: Int: Not used : irq 255
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : Unlimited
Failover : Disabled
VPN-DES : Enabled
VPN-3DES-AES : Enabled
SSL VPN Peers : 2
Total VPN Peers : 10
Dual ISPs : Disabled
VLAN Trunk Ports : 0
Shared License : Disabled
AnyConnect for Mobile : Disabled
AnyConnect for Cisco VPN Phone : Disabled
AnyConnect Essentials : Disabled
Advanced Endpoint Assessment : Disabled
UC Phone Proxy Sessions : 2
Total UC Proxy Sessions : 2
Botnet Traffic Filter : Disabled
This platform has a Base license.
Serial Number: JMX1253Z0S8
Running Activation Key: 0x5c28fa75 0xe089c41e 0xf02395e8 0xa3ac7cb0 0x892089b8
Configuration register is 0x1
Configuration last modified by enable_15 at 09:10:02.342 UTC Mon Nov 12 2012
ASA5505#
11-12-2012 09:42 PM
The ASDM version is not compatible with the ASA version that you have.
Pls kindly upgrade the ASDM to version 6.3.5 or later.
Here is the release notes for your reference:
http://www.cisco.com/en/US/docs/security/asa/asa82/release/notes/asarn82.html#wp309157
11-13-2012 05:33 AM
Thanks! This has been most helpful. I do have another question though. I am a registered user and have gone to the Cisco software download site but cannot seem to find any link to the ASDM software upgrades. I know they have to be there but I have looked for an hour and have even searched for "ASDM 6.3" with negative results.
Can you point me a little closer to my target?
Thanks
11-13-2012 03:14 PM
Sure..
From the main download page, go to:
Security --> Firewalls --> Adaptive Security Appliances (ASA) --> Cisco ASA 5500 Series Adaptive Security Appliances -->
Cisco ASA 5505 Adaptive security Appliance --> Adaptive Security Appliance (ASA) Device Manager --> You should be able to find 6.3.5
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide