VPN

I have 4 ASA 5505's with Site-to-Site IPSEC VPN tunnels built between them.  One of the tunnels stays up just fine but the other 2 drop at the end of the SA lifetime for a period of time equal to 10% of the SA lifetime.Orignially, I had the the lifet...

Okay guys so I am having some issues!ASA 8.2ASDM 7.1I have created a SSL VPN using the wizard I selected both clientless and anyconnect. I am able to get to my portal page and login but am not able to get to anything using the cifs:// ..... Oddly eno...

When I install the Cisco VPN Client 5.0.00.0090 on my Vista laptop while connected to my office LAN it works fine. When I go home and connect to my home LAN I get the Reason 442 error. If I uninstall and reinstall while connect to the home LAN then...

Hi,I am having issues trying to setup an ASA as an Easy VPN hardware client, the other end the Easy VPN server is a Router, the issue is the ASA is displaying as connected “AM_ACTIVE” but am unable to access any of the networks on the other side of t...

Hey guys! So I am having some issues setting up my SSL VPN. I have selected both clientless and anyconnect.runningasa 8.2asdm 7.1I can acess the portal but the issue comes into play when I try to use cifs:// it says error connecting to host. But its ...

HI,I AM HAVING AN ISSUE THAT ASA 5505 BLOCKING ALL INCOMING TRAFIC FOR SPECIFIC INTERFACE CAUSED BY IMPLICIT DENY RULE, I HAVE TRIED TO CREATE A PERMIT ACL STATEMENT, BUT IT DIDI'NT WORK.SO PLEASE HELP MEPLS SEE THE ATTACHED SNAP SHOTOF THE ISSUETHAN...

I am trying to trouble shoot a Site-To-Site VPN routing issue. I am trying to understand how the routing process works for Site-To-Site VPN traffic to and from the local LAN and the rest of the corporate network. For instance, looking at the attached...

Hi,I have an  IP Telephony setup with CME 9.1 (2921 router) and having 4 remote sites connected with site to site VPN.All the remote site phones are connected to main office Call Manager Express.Each site including 3 Cisco IP Phones only.We are havin...

Hello,In our environment we have a Zone based firewall on CIsco ASR 1000 XE router, terminating normal IPsec VPN sessions on ZBF. The router has one outgoing physical interface (g0/0/0) connected to ISP as outside Interface and multiple Interfaces on...

Situation:-RV042(v3) with latest firmware (as of today)-Remote user behind a Cisco ASA 5505 (runing 8.4 firmware) is not able to connect using the QuickVPN client-Quick always fails the "Verifying network" phase-QuickVPN can connect from other locati...

Hello Guys,I am deploying IPSec VPN over MPLS L3 ADSL link between HeadOffice and different branch locations. VPN tunnels are up and running i can successfully ping both sides. But the browsing is very very slow. Users at remote sites cannot browse t...

      I am working on GNS3. ASA to ASA  VPN is working fine without any issue. When I try to establish IOS to IOS VPN it is not working. Phase1 itself not coming up. Anybody worked on this issue. Your reply highly appreciated             

Trying to build L2L VPN with AWS VPC.  Run into problem at the Phase-2.local3.notice %ASA-5-713119: Group = xx.xx.xx.xx, IP = xx.xx.xx.xx, PHASE 1 COMPLETEDlocal3.err %ASA-3-713061: Group = xx.xx.xx.xx, IP = xx.xx.xx.xx, Rejecting IPSec tunnel: no ma...

Please i need help to open port 5060 tcp and udp , range of ports 9000 to 9015 from out side to inside server 192.168.11.4 behind NAT/PAT , i tried many solutions but not worked with me ThanksMy Configuration : version 12.4no service padservice times...