VPN

Hi all, i hace a VPN configured between two Cisco ASAs, but I have a problem to reach a network behind a router 2800.Let me explain.LAN (inside:10.2.69.0/24)---ASA1<--------->VPN<-------->ASA2-----LAN(10.2.0.0/24)---------ROUTER 2801(172.26.0.1/24)Th...

I put a new version of Cisco Secure Mobility Client into the AnyConnect Client Software.  I put this version ahead of an old Anyconnect 2.5 version.  After I save the change, I cannot connect using the old 2.5 version.  Is there a way to update the s...

Hi all , i am setting up Clientless VPN and Anyconnect . i have created a connection proffile and group policy and everything is working fine. however i am confused as to how i set up per-user rules? I am using AD to authenticate users to log in but ...

Quick I promise.  If you have two remote clients with DHCP outside addresses, connecting to your ASA which is static, so both tunnels are initiated on the remote end, with your dynamic crypto, one requires PFS one does not.  How do you do it?And yes ...

Hi guys,Im having an issue with my VPN. I have configured 2 VPNs on my firewall. Site to site and Remote Access.Problem is I only have 1 outside interface. If I assign the remote access crypro map to Outside interface, the site to site VPN stops work...

Hello all, I'm hoping to get some feedback on a scenerio, that I'm unsure is possible given certain parameters:We are looking into putting a remote site in place that at this time, can not have any major wan connection (MPLS, T1+, ect) but must rely ...

Hello everyone,I'm struggeling to get a DMVPN to work over an IPv6 WAN Network. I have testet IPv6 connectivity from the Spoke (2001:2:2:2::1/64) to the Hub (2001:1:1:1::1/64) which is successful, there is also an IPv6 default route to my "ISP", I al...

Greetings to the CommunityI am trying to figure out a clean solution for the following scenario. I have my PIX 515E (8.0(4)24) configured for VPN access. In the VPN configuration, I am using an RA tunnel group configured to use Windows 2003 IAS to au...

Hi allcan anyone tell me how the vpn filter works on the ASA, Also I have ticked the box that says bypass interface access lists, however the inside to outside access list on my interface is blocking the vpn traffic going out. I thought the tick box ...

Trying to keep what seems like a convoluted problem fairly simple.For this particular problem, I have 4 interfaces on the ASA 5510 (untrust, trust, prod, dmz), 3 subnets and a single VPN network.VPN network = 10.1.55.0trust interface = 192.168.1.0pro...

Hi!I have a  question regarding certificate-handling in the ASA (for example for  using it for AnyConnect).I'm not talking of the internal CA  here, just about handling certificates coming from an external CA.If  you configure a trustpoint on the ASA...

Hi everyone,I've been digging around the forum and haven't found a solution to my issue.I configured an old 1711 router for a home office setup while waiting for Skydrive. They have a fairly old cable modem only capable of forwarding tcp/1723 for PPT...

I can't seem to find any clear documentation on this. I can find documents on mapping users to a group policy based on AD group membership. I'm simply wanting to put all our VPN users into an Active Directory Group and only these users can authentica...

Hi everybody,I'm using ASA 5510 I have two inside interfaces my endoutside:  a.a.a.ainside1 : b.b.b.b/24inside2 : c.c.c.c/24other end outside: d.d.d.dinside : e.e.e.e/29There is tunnel established between b.b.b.b/24 and e.e.e.e/29I'd like to route th...