VPN

Hi All!I am wondering if there is a way to make a sort of redundant VPN connection using following equipment and technologies.I have a couple of ASAs in  my office and around 100 remote VPN connections to connect to the ASAs  that I have in my offic...

When using AnyConnect version 2.5.3054, the client fails to connect to an ASA that has either one of the following versions of CSD installed - 3.6.185, 3.6.1001 and 3.6.3002. The endpoint assessment fails. A pop up window appears...Posture Assessment...

Client: CISCO VPN ClientVPN server: Cisco Concentrator 3020  OS v 4.7I want to get away from configuring split tunneling for security reasons. With Split tunneling and I am able to specify to which subnets the clients have access to. I do it defining...

I'm new with the Cisco Support Community and I'm here because I have a VPN issue.  This one seems to be stumping most people around me.  I'm hoping this question can be answered here.  I just uninstalled Cisco VPN and reinstalled it.  I am able to VP...

I am working on an ASA that is running version 8.0 (4). Does this error cause the SSL VPN portal to not show Cisco logo along with not displaying start anyconnect once I login?float-fw-01(config-webvpn)# enable ExternalERROR: entry for address/mask =...

Hi,we installed an ASA5505 an we configured a vpn l2l to another asa.unfortunately this vpn tunnel sometimes goes down and do not come up again, in order to keep it up we need to have a continuos ping to generate traffic inside the tunnel.How is poss...

When I try and ping a remote address on my vpn 3000 concentrator I get ttl exceded. When I try and tracert from my workstation to the remote address on my vpn 3000 I see a loop. Tracing route to x.3.17.145over a maximum of 30 hops:1    29 ms    31 ms...

Dear All,now i have problem with speed throughput not full on VPN site to site wiht ASA 5510 and ASA 5505.Let me tell all of you that i use fiber connection from HQ to Branch with speed 10MB/s and i configure VPN site to site from HQ to branch.and my...

Hi Everyone,I have an odd situation where I need to config site to site VPN with a very "tight" VPN ACL that allows access to a specific port and host at each end. I need to tunnel TCP traffic from site A encryption domain address 1.1.1.1 to site B a...

Hi All,I'm aware that you can authenticate and authorise end-users using either Radius or LDAP on an ASA for remote and or Admin users? But was wondering if you can combine the two so authentication is done via Radius and LDAP for authorisation i.e. ...

I have a CISCO RV 120W router. I have set it up with a static IP address from Verizon. Internet can be accessed.I just want IPSec passthrough for some people who can connect with Nortel contivity client to the company RSA server. I can make only one ...

I'm trying to achieve framed-ip-address/static ip address for some remote access vpn clients and ip allocation from pool dynamically for remaining remote access vpn clients. I've configured my asa with the help of http://www.cisco.com/en/US/products/...

Hi Guys,On my setup SSLVPN tunnel fails with AnyConnect 3.0.3050 or above releases to UC520 platform running IOS(151-2.T4).3.0.42353.0.30543.0.3050Connection succeeds with all other versions below 3.0.3050. I’m using standalone client on my PC (tried...

Folks, New to the board, So I'll say in advance I appreciate any constructive feedback someone might offer. My networking experience isnt that of a certified network professional. However I've done an adiquate job thus far at figuring things out on m...

Guys we have a environment where we have a ISP router which is conected to VPN concentrator and then its connected to PIX......all devices are end of life and we will be replacing them.............there are 40 customers which have a VPN conections wi...