Hi, I have a connection between HQ and Branch which connected by GRE tunnel over IPSec. I use Cisco router 3745 that has IOS version: 12.3(18) and Cisco router 2911 that has IOS version : 15.0(1r)M9 with ipbase, security and data license. I t...
Is there any way to isolate the bandwidth a tunnel is getting through an ASA?And is there any way to isolated the tunnel's packet loss/fragmentation OUTSIDE or INSIDE?
Hello,I have to configure a few cisco asa 5510's for VPN remote access using l2tp ipsec. One of the requirements is that no additional vpn clients be used to connect. We only want to use the client included in Windows 7 x86. Is there any documenta...
Hi guys,I have VPDN running on our Cisco 1921 router running 15.2(1)T. Previously I was using Cisco 2801 router running 12.4(24)T4. I copied the config from the 2801 to the new 1921 router before replacing the router but now the VPDN isn't working.Ba...
Hi,We have fresh and new ISR1921 here. We actually have a PPTP VPN for our external users. I am actually trying to assign some specific ip address to someone who connect via the VPN but I can't achieve this. Here is the configuration:interface Virtua...
Hello,I'm using an ASA5510 for remote access IPSec VPN clients and it is configured for split-tunnelling. The client computers are running Cisco VPN client software. All of the client computers running Win 7 work perfect, but the client computers r...
I've recently been tasked with providing access to several internal servers to a remote site via one of our ASAs. In order to keep things simple, I have begun by creating a single static NAT rule for one of the servers. The Site-to-Site VPN connect...
All,I have created a second site-to-site VPN connection from my remote site to another site and I have the following issue when I ping from Site B to Site A:"Routing failed to locate next hop for icmp from NP Identity...."If I ping from site A to sit...
Dear AllI was configure IPSEC vpn on ASA5540 and i have problem with port blocked. I am unable to block server ports to remote users. See below configuration. I need to configure vpn filter list can any one help me to configure vpn filter list. ...
Dear Support,We have the following scenario:1. A VPN site to site on ASA between three branches: Headoffice, Hamra branch and Dora branch2. All branches are connected through Two WAN connections: PESCO as a primary connection and DSL as a...
Hello.I need some support about this problem.I need to apply to my network card, an IP in the range of the IP of the Remote VPN Network.I know that I can not apply 192.168.0.X (adding it to my TCP/IP config) to my network card (now I have 192.168.5.X...
Hi People,Can anyone help..I have a established VPN between NS500 and AS5505The following diagram shows whats going on.customer source subnet: 192.168.2.0/24Source NAT to 10.160.64.33NS500: sub int 1.3 : 10.160.64.1Destination NAT to : 199.53.28.17...
I am Network Enginer in small business company. We have around 20 nods /branch/. We using CISCO 871 router about 2 years.Currently ,there is problem emerged. Our routers drops the Tunnel /VPN connection. Then when i saw the log it is llike this: ...
Hi All,I have a ASA5510 (EasyVPN server); and a ASA5505 (Easy VPN extension mode).On ASA5505, I had "internal interface" with 10.10.110.254/255.255.255.128; and "DMZ" 10.10.110.1/255.255.255.128The ASA5510 had internal ip range with 192.168.159.254/2...
I have an RV042 with the PPTP server configured, which is working because I can connect with my iPad and droid phones, however, I'm unable to access resources on the RV042 side (192.168.1.X) when my local network is the same ip scheme (192.168.1.x). ...
